brake fluid cap 3d models
93052 3d models found related to brake fluid cap.thingiverse
Here's the source model for adjusting: https://www.tinkercad.com/things/7JAe1vDGpbW-brake-fluid-cap/edit My first prototype (that seemed to work after re-shaping), had no grip so I added edges, as well as adjusting the measurements slightly. Safety...
cults3d
1/3 turn plug for the brake/clutch fluid jar of FORD Fiesta from 2013 to .... Essential for pressure bleeding with an EEZYBLEED device. Never part of the standard plugs supplied with the bleeding devices (screw-on plugs only). ...Tested 100% OK using...
thingiverse
Just a quick design of a brake fluid cap with attachment for a hose, for bleeding brakes.
prusaprinters
Just a quick design of a brake fluid cap with attachment for a hose, for bleeding brakes. Print Settings Printer: Sapphire Plus Rafts: No Supports: Yes Resolution: 0.2 Infill: 10 Filament: 3d Jake PLA PLA Orange Notes: i printed it upside down,...
thingiverse
Cap for brake fluid tank on Nissan Qashqai tested on J10 car, for temporary usage! Don't forget about rubber gasket! Model w 3 digit is updated version and sitting more precise then previous. ... ps may need some file work
thingiverse
A friends jeep brake fluid reservoir broke and asked if I could 3d print one, so I did. ...Printed with PLA, it's been working for more than a year now
thingiverse
These are the two caps for the brake fluid reservoir for a 1977 Toyota Celica. Probably they will fit other years and models, too. Dimensions (outer diameter of the reservoirs) Big cap: approx. 63.5 mm (2,5 in) Small cap: approx. 49.6 mm (1,95 in)...
cults3d
... brembo cap fit on rear brake fluid reservoir Ducati Hypermotard 1100 2009, *Letter b on cap top watermark, is align for rear brake. ... New Version https://cults3d.com/en/3d-model/tool/ducati-rear-brembo-brake-fluid-reservoir-cap-custom-john_vlahidis
thingiverse
No supports Nedded, Print in ABS for longevity or PLA is fine but replace it every year or so. I couldn't test it on other models but works great in the Mini Countryman R60 2011 and BMW X1 2014. The original cost like $35 USD. ...If you like it...
cults3d
This is custom with letter "b" from brembo cap fit on front clutch fluid reservoir Ducati Hypermotard 1100 2009, *Letter b on cap top watermark, is align for front clutch fluid reservoir (and had height 1mm).
cults3d
This is custom with letter "b" from brembo cap fit on front clutch fluid reservoir Ducati Hypermotard 1100 2009, *Letter b on cap top watermark, is align for front clutch fluid reservoir (and had height 1mm).
grabcad
Frond badge fits Opel Corsa B. ...Cap covers fits as they are signed, that they fit C20XE, X25XE, X30XE, C25XE Please visit: https://www.facebook.com/pages/STELMACH/286353431402978
cults3d
This is custom with letter b from brembo cap fit on rear brake fluid reservoir Ducati Hypermotard 1100 2009, *Letter b on cap top watermark, is align for rear brake.
thingiverse
Als Dichtung kann ein 1 1/2" x 2mm (44,5mm x 35,5mm x 2mm) Dichtungsring aus dem Sanitärbedarf verwendet werden Cap for the brake fluid reservoir (in the engine compartment). Standard Euro E20 thread. Compatible with many brands. Tested on a Ford...
thingiverse
Redesign of previous Thing that did not work properly. I had to delete the previous version due to a Thingiverse bug. Made this one more flexible to get on and off without snapping. Printed and used successfully with PLA (eSun). Might be...
cults3d
... part number 10.2704.60 Had 2 files The file name start with [ORIGINAL dimensions.x.x.x.x.x] is close to original part dimensions. the other file [Brembo Brake Fluid Container Reservoir Cap Part 10.2704.60.stl] had little tolerance for my 3d printer
cults3d
... Cap With letter "b" Had 2 files The file name start with [ORIGINAL dimensions.x.x.x.x.x] is close to original part dimensions. the other file [Brembo Brake Fluid Container Reservoir Cap Part 10.2704.60.stl] had little tolerance for my 3d printer
thingiverse
This is a model of the brakefluid reservoir from a BMW F800R (2011) and 2 Versions of a Cap/Guard. Use it or make yourself a new Cap/Guard. ... I build it to cover more than 50% of the diameter and it snaps to the reservoir without any straps
prusaprinters
Cap of my brake fluid bleeder jar was damaged. The top of the cap was cracked and I tried to glue it without success. As I cannot find just the cap on the market, I decided to design and 3D print oneDesign done using Fusion 360 from original cap and...
myminifactory
This 3D print is the small acorn shaped cover to the low brake fluid light switch. My original deteriorated long ago, and pressure bleeding requires a tight seal of the entire brake reservoir. ...Mine was printed using a semi-soft, rubber like plastic...
thingiverse
I am making an adapter with a threaded cap in order to more easily pressure bleed the brakes on my Toyota Tacoma. Normally one would use a "universal" adapter thingy with chains and a rubber stopper that is a real kluge and PITA. The cap for the...
cults3d
Small redesignation of the Vmax rear brake fluid reservoir cap, but can also be used on other models.
thingiverse
Print this part 2 times and you can fix you brake fluid container. ... use a m5 bolt and nut for it.