braun silk epil 7 3d models
208543 3d models found related to braun silk epil 7.thingiverse
... 0,4 nozzle for print and very slow speen with 100% infill. For models 5377 Silk-épil 9, Silk-épil 7 - SkinSpa, Dual Epilator, Legs Body & Face, Legs & Body, Legs / Silk-épil Xpressive / Super Solo / BGK 5378 Silk épil 9, Silk épil 7, SensoSmart
thingiverse
File gear_FDM.stl is adapted for FDM, gear_original.stl has original sizes. Nozzle: 0.2mm Material: nylon (something else it makes no sense to use) Sources are included. ... Modeling software is Kompas 3D
prusaprinters
I wanted to mount my Braun Silk épil 7 into my shower.So I remixed the wall mount from horrovac to mount with suction pads.The big hole is 16mm in diameter and the small is 10mm.The head of the suction pad is sunk 5mm.
prusaprinters
This print provide the model to replace the long gear inside the Braun silk-épil 9 that gets worn out quickly. The print was performed on a Prusa Mini with a 0.4 nozzle, supposedly a 0.25 nozzle would be better for such a small size. Print...
thingiverse
As the name says, it´s a holder for the Braun Series 7 shaver
thingiverse
Replacement foils are not cheap and unlike every other shaver that I've owned, my Braun series 7 wasn't supplied with a cover. Printed on end. It clips over the ridges on the sides of the "cassette". ... NOTE: Not the *current* series 7 with the...
thingiverse
Printed with Anycubic i3 Mega S Nozzle 195 °C Bed 50 °C 10 mm high 7.5 mm inside diameter 38 mm outer diameter Tested on "Braun PC1" All rights belong to the original designer.
thingiverse
This is a replica of a broket propeller of Braun Satin Hair 7 Fan.
thingiverse
Braun Series 7 Shaver Power Cord Holder, circa 2010 model I usually disconnect the shaver from the wall outlet after its finished cleaning because of an annoying high frequency noise it makes. To prevent the plug/cord from just dangling off the...
thingiverse
Replicated this coupler after the original one fell into the resistive element of the dishwasher and melted away :_( https://www.braunhousehold.com/en-au/products/food-preparation/hand-blenders/multiquick-7
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=48424 Instructions Using the following options: total_width = 95 desired_word = BRAUN total_depth = 5 finger_spacing = 23 total_height = 60 finger_size = 25
prusaprinters
Designed this wall hanger for a braun series 7 electric shaver. Can be mounted with double sided tape. ...Mounted mine inside the bathroom mirror cabinet.</p>
thingiverse
... den Haartrockner "Braun Satin Hair 7". ... Am besten Aufrecht drucken, dann sind keine Stützstrukturen nötig Auflösung: 0.2 mm This is a holder for the "Braun Satin Hair 7" hairdryer. ... Print it upright, so no support necessary Resolution: 0.2 mm
thingiverse
......The new one (Braun MultiQuick 7) didn't include one, so I created one. In the photo with 2 mounts, the white one is the original and the black one is my design. ... The mount can hold the hand blender, the motor part, or the blender part as needed.
cults3d
The Braun Mutiquick 7,9 Blender as one fail, the part joining the motors and the accessories is in plastic... if the load is to hight, the parts fails and you have to buy a new blender... I created these parts to replace the original one. Just pull...
thingiverse
I was trying to buy an Organizer for my Braun EasyClick Attachments, but there is noting to buy. So I decided to design my own. For 6 Braun EasyClick Attachments. - Beard Trimmer with all 5 attachments. - Stubbler with all 4 attachments. -...
thingiverse
This is a parameterized press fit replacement fan which I designed for the Braun Satin Hair 7. I simplified the design a bit compared to the original part. First print the test print pieces (yellow cylinders in the picture). Each test piece has...
thingiverse
Simply a rack for the Braun All-in-one Trimmer 7 Kit (MGK7320) and a nose hair trimmer (outer diameter 22.5 mm) or some other stuff fitting into that hole on the top right space of the rack (see pictures; I placed a nose hair trimmer of BaByliss -...
thingiverse
updated accessory holder without holding the main shaver
thingiverse
Remixed from H3ctor's [desktop holder](https://www.thingiverse.com/thing:1777117). I wanted a wall mount, and preferred to keep the lens filters in their boxes. The contours of his holder does a fantastic job, so I cut out out and tilted it 15...
thingiverse
What you need is some double sided adhesive tape. I recommend the 3M™ Adhesive Transfer Tape Double Linered 7955MP which sticks like poison. ... Once properly attached you could pull the tiles from the wall with that holder...