bruiser clone 3d models

**Check out my other socks for other hotends:** - [Version 1 - CR-10 Stock Hotend](https://www.thingiverse.com/thing:2848472) - [Version 2 - CR-10 Stock Hotend](https://www.thingiverse.com/thing:2879204) - [Version 3 - CR-10 Stock...

You need: * bondtech BMG extruder or clone * stepper driver extension cable * preferrably, a lightweiht pancake stepper motor, although the stock fullsized one will also do as a starter One additional benefit is, that you do not need to flash a...

Other parts I've designed for my Prusa i3 steel upgrade include: - http://www.thingiverse.com/thing:1959901 (GT2 belt clamp for the Prusa Y-axis) - http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case) -...

So, I'm going to turn it into a MK2S clone with bigger build volume (I get non-printed parts from AliExpress). I hope now that will make it a great printer. Pretty much just the frame, some bolts and three stepper motors are left from the K8200. The...

I have only tested this on a genuine BMG, I cannot speak for how a clone would fit. Just need 2 m3x6 screws and 2 m3 nuts. A couple things to note - 1. The stepper direction needs to be un-reversed in the firmware. 2. The motor sticks...

Hardware Used: FPV Receiver RD40: https://www.amazon.com/HankerMall-Empf%C3%A4nger-Diversity-Receiver-Quadcopter/dp/B075V54KFT/ref=sr_1_2?__mk_en_US=%C3%85M%C3%85%C5%BD%C3%95%C3%91&keywords=rd40+diversity&qid=1565639230&s=gateway&sr=8-2 Arduino Nano...

Although a printer is never fully feature complete, I think I've tweaked some parts for the better: * Rigid mounting brackets increase stability * A Z Endstop that doesn't need adjustment before every print * Belt Tensioner for X and Y Axis * Snap...

... If you can use it let me know! Instructions Printed it with no support and no raft. Depends on your needed size because of the overhanging parts and your printer setup. I used a makerbot clone.

Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: 0.2 Infill: 50% After printing both parts, thread the USB cable into your saved webcam PCB and solder it in place. You'll notice that the supports for the...

I highly recommend configuring the top three pixels on either side of the Y to be clones of each other by making a 3-way split with your WS2811 pixels. After that third pixel comes up from the bottom, the signal will go to both sides simultaneously...

So I bought the Titan Aero Clone from TriangleLabs hoping that this will fit correctly in the current mount, unfortunately wasn't. I tried this mount https://www.thingiverse.com/thing:4199867 and worked awesome at the beginning, but the motor...

As seen on the animated TV series Star Wars: The Clone Wars, the republic starfighter V-19 Torrent swoops in to defend its cruiser from a separatist attack! Help fend off those damned clankers by flying your very own! My other Star Wars kits: ...

It pushed my Ender-3 "clone" (JG Magic) printer to the absolute limit of the bed size, but I got it to work. Even at that low resolution, it took almost 10 hours to print. The gasket is almost entirely hidden when the set is assembled, so its...

I currently use either the full-size ESP8266 or a Wemos D1 (or clone) for my builds. For my latest projects, I typically implement the WiFi Manager, which allows me to set any WiFi network I need by simply pressing a push-button on startup. Once...

Design Process To create this design, I started by making a single hex cell, then cloned it and used copy and paste tools in Fusion 360 to generate an array of cells. I combined all the cells into a single object and rotated it 3 degrees. ...Next, I...

12428 crawler conversion/SCX10 clone mount kit here: https://www.thingiverse.com/thing:4629482 Check it out running on the YouTube: https://youtu.be/jw6EaQD7Egw You'll need M2 screws for assembly, or brad nails and glue, or a combination of both. ...

**The additional components visible in the attached renderings can be found below.** |Component|Source| |---|---| |LED Panel Indicators|[McMaster-Carr](https://www.mcmaster.com/2779K11-2779K111/)| |Emergency Stop...

FULL BOM: ------------------------------------------------------------------------ - 2x 5mm LEDs - 4x 100k Ohm resistors - 2x 220 Ohm resistors - Assorted wires (I used Dupont style connector type) - All components above may be sourced individually...

With fully integrated BLTouch or Clones mount (4 parts to print) - Main body - Flat Cable Protector - Air Fan Duct - ABL BL touch mount If you don´t use a bed level touch sensor on your X1 or Genius, no problem. You can still use these parts. You...

So I started this.Fun fact: Since 2020 I “restarted” dies project every X-mas ;-) This X-Mas I found a clone on Thingiverse - thanks Psy185!! - and that motivated me again to look at my own creation. So here it is.Is this smart?Is this a good idea to...

This is a cooling duct for a direct drive extruder setup on a CR10 or clone/related 3d printer. This was made to fit the printermods direct-drive plate with a BMG extruder directly attached to the triangle labs dragon hotend. It will also likely work...

The X gantry right side bearings on the Sintron i3 clone are directly linked to the X gantry itself. Meanwhile, the X-axis tension is solely controlled by how you secure the belt into the X carriage. If you prefer a higher belt tension, it has a...

I've tested this design on my MachCube2.0 and used a NEMA17 pancake stepper motor from a clone titan extruder. The Duet Wifi electronics have been configured with the following settings for the 10:1 gear ratio - further refinement is still needed: ...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

A minimal amount of time was spent on the design, its not overly complex and its small, to print 3 took about 1.75 hours in ABS with my print settings on an Replicator clone that has several upgrades. ... You can see in the photos where these attach,...

A few years ago when I set up my MP Maker Select Pro Ultimate (clone of Wanhao Duplicator 6), I found the provided spool holder to be less than satisfactory. Many spools were too wide, and it either seemed to unroll too easily, or get snagged and...

I used an M3 screw (20mm) and nut to fasten the base to the swivel, although if you prefer to use all printed parts, you should be able to use this set of fasteners: https://www.thingiverse.com/thing:192259 Print Settings Printer Brand: Prusa...

This jig was used to complete a G3K clone, and had to be slightly fitted for perfect fit to factory parts (minor sanding if parts are out of spec, perhaps a ring of tape around cylindrical parts where the jig sits on them to provide a uniform...

It fits over the existing socket head cap screws and the Case Base snaps right onto it.No hardware required!! Lots of people use an Ender 3 or a clone, so I made a bracket that fits the 40/20 rails used in the base of an Ender 3. This bracket uses 4...