btech uv 25x4 mods 3d models
118354 3d models found related to btech uv 25x4 mods.thingiverse
This is a set of rails / a cage for a BTech (BaoFeng Tech) UV-25x4 radio. It will probably fit the BTech UV-25x2, QYT KT-7900D, Radioditty QB25 Pro, and other clones. Both sides are pretty much identical, so just print two and use the black...
cults3d
This is a set of rails / a cage for a BTech (BaoFeng Tech) UV-25x4 radio. It will probably fit the BTech UV-25x2, QYT KT-7900D, Radioditty QB25 Pro, and other clones. Both sides are pretty much identical, so just print two and use the black mounting...
prusaprinters
This is a set of rails / a cage for a BTech (BaoFeng Tech) UV-25x4 radio. It will probably fit the BTech UV-25x2, QYT KT-7900D, Radioditty QB25 Pro, and other clones.Both sides are pretty much identical, so just print two and use the black mounting...
thingiverse
Replacement mounting bracket for BTECH UV-2501 mobile transceiver.
thingiverse
The knobs that come standard on the Btech UV-25X2 are rubber and easily slide off when using. ...I designed these in Fusion 360 as suitable replacements.
thingiverse
Basic pop-up wall blocks for your combat arena. ... If you are playing BTech, they are considered level two at 38mm tall with a hex base that is 33mm from side to side. ... [Normal hex map scale]
thingiverse
Pop up hew walls for arena combat, presented as individual hexes to allow for multiple maps or to design you own custom arenas. ... The hex base is the standard 33mm for BTech maps and the height is 38mm.
thingiverse
From the factory my BTECH Mini UV-25X2 radio had button/wheels that continuously fell off. I designed this to replace the existing button/wheel, and printed them in bright orange to make it easier to see and operate while driving without looking...
thingiverse
drive gears kit:https://www.aliexpress.com/store/product/3d-printer-parts-1-kit-Drivegear-dual-drive-gear-extruder-kit-Cloned-Btech-upgrade-for-i3/3375006_32948684255.html?spm=2114.12010608.0.0.34e25b9dPgm9Dh or...
thingiverse
Mounting cradle for Btech DMR-6X2 handheld radio, designed to be fitted with RAM-B-348U ball in rear for use with RAM mounts (or compatible.) A 1/4"-20 ~1/2" long bolt or screw is required to hold the RAM ball in place. This mount should work...
thingiverse
My 3d printed dual drive 3 to 1 gear (Hercules) extruder designed with the use of Btech Dual Drive Gears. It has the same gear ratio as Bondtech BMG extruder with estep of 415 Parts required - PTFE tube - 2 x 625zz bearings - 1 x M5x40mm screw...
thingiverse
Speed Graphic Quarter Plate 3.25x4.25 Lens Boards Blank 1.5mm thick "Center mark is for a 6mm or 1/4 inch drill bit hole saw" Compur 33mm hole Copal 0 Copal 1 Graphex 90mm Graphex 135mm
thingiverse
This is not my design... It belongs to Bondtech and is licenced under Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. The BMG Assembly instructions. ... https://www.youtube.com/watch?v=dTUppEUFXVE ...
thingiverse
I needed a way to mount/hold my BTech DMR-6X2 portable radio while mobile. This was designed for use with a belt clip and with or without a battery eliminator. I decided not to incorporate the RAM ball mount in to this design since there are many...
thingiverse
Here is another minimalist desk stand for one of my favorite HT's...The BTech GMRS-Pro. It uses the belt clip and battery latch to attach itself to the radio. This stand is very helpful for this particular radio since it has a hard time standing on...
thingiverse
Customized version of http://www.thingiverse.com/thing:536486 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=536486 Instructions Using the following options:...