btt u2c mount 3d models

These box designs have mounts for the BTT Octopus, with or without two MOSFET boards, and a 120mm fan; power from your supply can be snaked in through any of the many hexagon holes to suit your needs. The hexagon holes are also useful for wire ties....

I remixed this to fit the BTT version of the Mini 12864 Display, it's a little different. I also made a few other changes and added the Voron logo and inlays for 2 color if you want. I had to redo the supports for the SD card slot (parts 2, 3, 4). I...

You can use the small switch on the display to change its orientation.Bugs:After making this case, I found an bug in the BTT Pi TFT70 V2.0 design in that if you mount the Raspberry Pi directly to the mount standoffs on the back, its PCB touches...

This is my "Legroom" remix of the BTT Smart Filament Sensor Mounting Bracket for Micro-Swiss Direct Drive Kit With Wrapping Legs (long-ass name) It lets you mount your smart filament sensor directly above the Micro Swiss Direct Drive extruder. The...

BTT_Octopus_rear I opened it up so you have more straightforward access to the power connections BTT_Octopus_top_Board_Only I wanted to use a 60mm fan I had on hand plus the top lacked the flair the rest of the case had so I added in the hex pattern...

2) BTT_Octopus_rear I opened it up so you have more straightforward access to the power connections 3) BTT_Octopus_top_Board_Only I wanted to use a 60mm fan I had on hand plus the top lacked the flair the rest of the case had so I added in the hex...

This is an enclosure for the BTT SKR 2 or BTT SKR 3 mainboard for Ender 3 printer. I also changed the original fan to Noctua silent fan, which is slightly wider than the original, so it should fit with the original too. The enclosure is...

This is a remix however the remix is not working so the link is below: https://www.thingiverse.com/thing:3127377 I wanted the display to be flush mounted when not in use and pulled out when I need it. Choosing this existing Ender 3 & Ender 3 Pro...

Remixing aslak3's design to suit a BigTreeTech v3 3.5" TFT Display instead of the MKS TFT. ... I discovered other remixes tailored for BTT displays, but none that would seamlessly integrate with the v3 model featuring a dual-function scroll wheel.

... branding. ...It's suitable for mountain bikes (MTB) or bicycles in general (BTT). ...The specific model mentioned is the Thomson Elite X4 at a 10-degree angle, measuring 100mm long and compatible with a 31.8mm stem diameter [Ref SM-E139].

The BigTreeTech Smart Filament Sensor Bracket made by Hans is great! If you have M4 screws, just use this remix, otherwise check out the original one.

Suporte para BTT EBB42 com abas para prender fiação. ... Usar com 1 arruela em cada parafuso do motor, separando a peça impressa do fundo do motor, de modo a permitir o resfriamento do motor e não derreter a peça impressa, Usar apenas abs, pois o motor...

The original print didn't work for the BTT SKR E3 Turbo board I had, so I moved things around to make it fit. ...I hardwired my power supply and I had no need for multiple holes for wiring, so I made a slightly larger rear hole for everything.

Left panel remix to house the TFT35 E3 V3.0 BTT display by Be Levi The design has not yet been tested, it has been made based on the measurements found on the internet. ...If you find any bug, it would be of great help to indicate it in the comments for...

After adding 2x BTTMOS mosfets to my printer to control the nozzle and bed temperature I also just added two spacers and a mosfet holder to mount them externally to the case and still keep the cables tidy! DISCLAIMER: As all the cables are...

Left panel remix to house the TFT35 E3 V3.0 BTT display by Be Levi The design has not yet been tested, it has been made based on the measurements found on the internet. If you find any bug, it would be of great help to indicate it in the comments for...

Stronger - the backplate for the BTT was crumbly at the edges - made it thicker aligned - the holes in the BTT - seemed a tad short and out of line so tuned up aligned - for my metal extruder head hole, and to get around the z screw - this works...

Model designed to adapt the BTT SPI display in the Sapphire Pro and Plus (which use the MKS TFT 35) It probably fits other printers that use this same display The model can be made with any filament It was designed to allow a simple fit between the...

A replacement for the front panel of the Creator Pro to house the BTT TFT24 screen. *This does not have an opening for the SD card* I am using an SD card extender, and a wifi adaptor for my SKR 1.4. A quick model for those that have upgraded...

I included the other pieces you will need to make it a full case but credit for the original design goes to twhite0101. BTT_Octopus_front The ports did not line up with my board so I edited it until they fit and added a bit more bevel around the SD...

I modeled this scratch using the original bracket and stepper as a guide, then added a place for a PTFE connector that lined up with the BTT Smart sensor. The model has a built-in M10 thread to be able to easily screw a M10 PTFE connector into it, ...

and are labelled. I also added cutouts for the CR10's stock power plug, main switch, hotend and bed connectors as well as mounts for a 60x25 front fan and 40x20 rear fan for cooling the electronics! There are also holes to organize all the cables...

Moving my files from Thingiverse, you can now find them here: https://www.prusaprinters.org/prints/22318-btt-tft35-v30-lcd-cover-for-mk3s-bear This LCD cover is specifically designed to fit the Big Tree Tech TFT35 V3.0 display on a MK3/S Bear frame.

This enclosure is for the Ender 3 v2 power supply and the BTT Manta M4P Motherboard. I printed this out of PLA with .2mm layer height and tree supports. You might be able to get away with no supports but I found there were some areas that didnt...

I really love this version of the PCB Cover with drawers https://www.thingiverse.com/thing:4570890, but i recently upgraded my Ender 3 Pro's screen to the BTT TFT35 and unfortunately the existing design doesn't cater to 1. the extra USB and SD card...

Upgraded to a BTT TFT35 and the SD and USB ports were covered. Also the bracket did not sit right and caused the display to flicker on and off; on the speaker corner and the control knob pcb offset piece. My first attempt with FreeCAD. Added the...

CompatibilityBTT PI TFT43 DIPRaspberry Pi 4Print InstructionsUse Default Prusa Slicer 0.20mm Quality Print SettingsNozzle Diameter : 0.40mmFilament : PLA or PETGInfill : Gyroid 25%Perimeters : 3SupportsSupport on build plate onlyXY separation :...

This cover for the BTT 128x64 MINI LCD resembles a Prusa i3 MK2-3 LCD cover, but the mouting system is a bit different. Print everything as oriented in the STL (the holders with the "wings" on the bed, the cover with the front down), with your...

Housing for a BTT Octopus (Pro) on Ender 3 (Pro), with TFT35 V3.0, MOSFET and Raspberry Pi 4, 2ea 80x80x15mm Fan Only screws, nuts, washers and sliding blocks are required for assembly. Printed in PETG with 0.6mm nozzle. There is still room in...

This is a case for the BTT SKR Mini E3 and the TFT35-E3 V3.0, designed as direct physical fit upgrades for the Ender 3 and similar printers to be used on other machines with 20mm pitch v-slot or t-slot aluminum extrusion frames. Built in SolidWorks...