build 5.8 ghz antenna 3d models

906287 3d models found related to build 5.8 ghz antenna.
5.8 GHz Helical Antenna
5.8 GHz Helical Antenna
thingiverse

Helical antenna for 5.8 GHz, designed in CATIA. Print out the mandrel and antenna support, then wrap a solid copper wire around it in the groove. Twist the wire into the support, solder a connector and backing plane on, and it should work. Some...

5.8 ghz antenna cover
5.8 ghz antenna cover
thingiverse

5.8ghz antenna cover Instructions you need to print this in 0.2 hight 50 mps and snap together the bottom and the top Piece and if tou need you can gleu the bottom piese to the antenna

Antenna protection AOMWAY 5.8 ghz
Antenna protection AOMWAY 5.8 ghz
thingiverse

Antenna protection AOMWAY 5.8 ghz Integrated protection without cable ties ;-) No sharp corners to avoid to hook the obstacle. It's possible to use the glue to close the assembly. Do not press the antenna during assembly, use a screwdriver to push...

5.8 GHz Pagoda Antenna Shell
5.8 GHz Pagoda Antenna Shell
prusaprinters

Shell for a 5.8 GHz 'pagoda' type antenna (by Maarten Baert). Tested with an antenna built from a Farview kit, fits nicely. ...The two halves can be glued, or just use 30mm (or larger) heat shrink to hold them together. This is improved over the design...

5.8 GHz Cloverleaf antenna pattern
5.8 GHz Cloverleaf antenna pattern
thingiverse

... hole is for RG59 cable (6mm diameter) Final fix with hot glue. 3 leafs for TX, 4 leafs for RX antennas. Take a look at my parachute systems and electronics for quadcopters at www.33dev.ru Print Settings Rafts: No Supports: No Infill: 5% is enough

Pentalobe Squarepants 5.8 gHz FPV antenna
Pentalobe Squarepants 5.8 gHz FPV antenna
grabcad

Gig to make a five lobe LHCP 5.8gHz (5780hz) Rx/Tx antenna set for FPV. Use the bending tool to make the lobes and a balun (26mm). Secure the lobes with five M3x5mm screws while soldering the lobes to the RG402 cable. Then twist the balun around a...

5.8 GHz 12 Turn Helical Antenna
5.8 GHz 12 Turn Helical Antenna
thingiverse

This is a laser cuttable version of the RcHobbysUK 12 turn helical antenna.

5.8 GHz Antenna Holder Field Box
5.8 GHz Antenna Holder Field Box
thingiverse

In case anyone wonders using soft wire for antennas is great as they just get bent up when you crash. You straighten them back out by hand and keep flying. I have had to rebuild a lot less antennas doing this so far. ... Only downside is they don't...

5.8 GHz Antenna Holder Storage Box
5.8 GHz Antenna Holder Storage Box
thingiverse

Wanted a safe way to keep my antennas stored at home or in the flight bag so they don't get bent up. ... I adjusted the box to lid interface for a 0.5mm clearance to compensate for the accuracy of my particular printer.

FlyTime 5.8 GHz Pagoda Antenna Shell
FlyTime 5.8 GHz Pagoda Antenna Shell
cults3d

Shell is connected by https://www.banggood.com/custlink/GGKK0IJ9kQ Original antenna is available at https://www.flytime.cz/fpv/flytime-pagoda-3-rev-b-antena-designed-by-maarten-beart-rhcp-lhcp/ Or you can but...

Cloverleaf antenna cover 5.8 Ghz
Cloverleaf antenna cover 5.8 Ghz
thingiverse

... on Thingiverse, but it didn't fit it's own cover. The cover is the simplest dome I could make to print easily (you can extend the bottom of the dome for taller antenna.) Instructions Very simple print, turn the dome upside-down for FFF printers

FlyTime 5.8 GHz Pagoda Antenna Shell
FlyTime 5.8 GHz Pagoda Antenna Shell
thingiverse

Shell is connected by https://www.banggood.com/custlink/GGKK0IJ9kQ Original antenna is available at https://www.flytime.cz/fpv/flytime-pagoda-3-rev-b-antena-designed-by-maarten-beart-rhcp-lhcp/ Or you can but at:...

5.8 ghz FPV BIQUAD antenna
5.8 ghz FPV BIQUAD antenna
thingiverse

100 % use 0.6 mm wire 102 % for 0.8 wire copper reflector 53 x 53 mm

5 turn Helical FPV antenna (5.8 GHz)
5 turn Helical FPV antenna (5.8 GHz)
myminifactory

There are several good 5.8 GHz helical antennas available already, but I wanted one that offered full protection for the wire, was compact and easy to print and did not require using glue for assembly. My design consists of two items that are held...

5 turn Helical FPV antenna (5.8 GHz)
5 turn Helical FPV antenna (5.8 GHz)
thingiverse

There are several good 5.8 GHz helical antennas available already, but I wanted one that offered full protection for the wire, was compact and easy to print and did not require using glue for assembly. My design consists of two items that are held...

5 Turn Helical Antenna for FPV 5.8 GHz
5 Turn Helical Antenna for FPV 5.8 GHz
thingiverse

Variation on a 7-turn helical antenna for FPV, converted simply into a 5 turn model. This will give a wider radiation pattern. ...Not as much gain, but you don't have to point it directly at the model as much.

Helix Antenna 5.8 GHz Quadrifilar case & mold
Helix Antenna 5.8 GHz Quadrifilar case & mold
thingiverse

Helix Antenna 5.8 GHz Quadrifilar case & mold based on the video https://www.youtube.com/watch?v=InLEq04R5So&t=348s

5,8 GHz 3/5-turn helical antenna
5,8 GHz 3/5-turn helical antenna
thingiverse

5-turn, -3dB beam width is ~48deg. At 10m far, beam is 8m width.3-turn, -3dB beam width is ~62deg. At 10m far, beam is 10m width. Instructions Glue pillars together. Pillars works both right- and...

Realacc 5.8 Ghz 5dbi Antenna Guard Protection Cover
Realacc 5.8 Ghz 5dbi Antenna Guard Protection Cover
thingiverse

Realacc 5.8 Ghz 5dbi Antenna Guard Protection Cover Use a zip tie to fix both parts together. ...Print Settings Printer: Delta Rafts: ...

5.8 GHz Triple Feed Patch Antenna Cover
5.8 GHz Triple Feed Patch Antenna Cover
thingiverse

5.8 GHz Triple Feed Patch Antenna cover for FPV This is for my Fatshark goggles. You don't have to use part 'B', that's the back cover, but the solder joints will be exposed. ... I got the antenna here:...

5.8 ghz helical antenna template (for FPV)
5.8 ghz helical antenna template (for FPV)
thingiverse

Template for a 5.8 ghz helical antennas (up to 8 loops). This template allready takes into account that the copper wire will bend back a bit. The measurements of the template are based on this calculater:http://jcoppens.com/ant/helix/calc.en.php If...

5.8 GHz Circular Paperclip Folded Dipole Phased Array Antenna
5.8 GHz Circular Paperclip Folded Dipole Phased Array Antenna
grabcad

... ...The angle of each antenna is 22.5 degrees and each antenna is designed for 5.8 GHz operation. The array should be phased for best directional range. ...The overall diameter dimension is 192.24 mm (7.57") and the overall height is 38.1 mm (1.50")

5.8 ghz helical antenna template (for FPV)
5.8 ghz helical antenna template (for FPV)
prusaprinters

Template for a 5.8 ghz helical antennas (up to 8 loops). This template allready takes into account that the copper wire will bend back a bit. The measurements of the template are based on this calculater: http://jcoppens.com/ant/helix/calc.en.php If...

FPV Boscam 5.8 GHz RC305 AV receiver antenna holder
FPV Boscam 5.8 GHz RC305 AV receiver antenna holder
thingiverse

Designed for: -Boscam RC305 5.8 GHz AV-receiver Might work with other, equally dimensioned AV-receivers as well ! Want to make one optimised for your box? ...I added the Solidworks-design files to the download list as well, so you can start...

5 GHz Helix antenna
5 GHz Helix antenna
thingiverse

... run a quarterwave segment of wire parallel to the ground to provide matching to 50 Ohm. Use antenna analyzer to check for impedance and reflected wave before transmitting. ... Sample usage: https://twitter.com/Sq3Swf/status/1314298124375072781

Antenna holder for Prodrone MicroVee 5.8 Ghz 7mm
Antenna holder for Prodrone MicroVee 5.8 Ghz 7mm
thingiverse

This antenna holder was designed for micro fpv quadcopters, where weight and space of the build matters.

7 turn Helical FPV antenna (5.8 GHz)
7 turn Helical FPV antenna (5.8 GHz)
thingiverse

It seems promising, since it would be easy to realize in many materials, but I have not made any design for it:http://home.etf.rs/~milanilic/publications/papers/AWPL-2006_01624449.pdfhttp://home.etf.rs/~milanilic/publications/papers/Olcan-Eucap06.pdf...

7 turn Helical FPV antenna (5.8 GHz)
7 turn Helical FPV antenna (5.8 GHz)
myminifactory

It seems promising, since it would be easy to realize in many materials, but I have not made any design for it:http://home.etf.rs/~milanilic/publications/papers/AWPL-2006_01624449.pdfhttp://home.etf.rs/~milanilic/publications/papers/Olcan-Eucap06.pdf...

Aomway 5.8 GHz omni antenna protector (The Balloon)
Aomway 5.8 GHz omni antenna protector (The Balloon)
thingiverse

This is my antenna protector for the Aomway omni directional FPV antenna. It consists of three parts, two bottom parts that goes on each side of the coax and then the top dome that screws on to the bottom parts, after that just put a zip tie at...

5,8 GHz antenna cover for cloverleaf/skew-planar
5,8 GHz antenna cover for cloverleaf/skew-planar
thingiverse

Little lower dome than source. ...Wall thickness ~1-1,5mm?? Installation in antenna assembly phase. ...Cable support for size RG316 and RG402