build my rack 3d models

Build plate rack/holder for up to 6 build plates. Max. thickness of build plates is 5mm. ...Works great for my Creality Ender 3 / CR-20 glass build plates (235x235mm).

Just a rack to hold your build plates when no in use.

I have a few printers, and couldn't find a suitable rack for both round and square build plates. ... I have it designed for a 260mm round plate or square plates of various sizes up to 5mm thick.

This is a completely overkill build plate rack. It has eight slots and is decorated with hexagons throughout. Definitely not the cheapest/lightest solution, but it's a pleasing way to store and dry your build plates vertically. ... Shown is with...

Based on the build plate Rack by Savagelt. I didn't like how it could tip over with only one plate near either side, so I redrew the design in Autodesk Inventor with outriggers. I also decreased the spacing of each rib so the plates stay more...

This is a simple more organic looking build plate rack with a wide base for better balance.It holds up to 5 sheets and can be used right off the print bed - use any type of sheets as long as the thickness is below 1.5mm, not only 3D build plate...

I recently purchased a few (8) glass cutting boards from the dollar store that work VERY well for build plates. I needed a way to store them and keep them out of the way at the same time so I designed this around a few pieces of PVC pipe I had and...

A filament bracket project for a 200x200 3D printer build. ...Comprises 3 components. i have updated the "filament rack L & R you will need to use these for your build.

... Sonic Mini 3d printer. ... To install, after the print finished, simply slides in and lock the rack with the resin vat nut. Fasten the build platform in an angle at the top. The space should be enough to hold a full size print w/ the hood on. ...

Simple rack to store the build plates for an ultimaker printer. Print e.g. ...in PLA with infill 20-30%, nothing fancy....no neat design, but does it's job :)

Knife rack made with a combination of 3D printed components, magnets, a walnut veneer strip, and a food safe wood finish. STLs are split into 3 parts that then need to be glued together. This should fit most 3D printers. ... Full build instructions...

Magnetic Knife Rack for the kitchen. STLs are split in 3 pieces to fit most printers, simply glue or use acetone (for ABS) to combine. ...Full set of instructions on how to assemble are available here: https://www.adylinn.com/blog/2017/kinferack

Magnetic Knife Rack for the kitchen. STLs are split in 3 pieces to fit most printers, simply glue or use acetone (for ABS) to combine. ...Full set of instructions on how to assemble are available here: https://www.adylinn.com/blog/2017/kinferack

Magnetic Knife Rack for the kitchen. STLs are split in 3 pieces to fit most printers, simply glue or use acetone (for ABS) to combine. ...Full set of instructions on how to assemble are available here: https://www.adylinn.com/blog/2017/kinferack

Magnetic Knife Rack for the kitchen. STLs are split in 3 pieces to fit most printers, simply glue or use acetone (for ABS) to combine. ...Full set of instructions on how to assemble are available here: https://www.adylinn.com/blog/2017/kinferack

I've also had a Hypercube build in the works for a while now, so I just raided what I needed from that.) I printed the plastic bits in eSun solid-purple PETG: https://amzn.to/2DR27Aw Some signficant differences between the stock A8 (or AM8) and...

I've also had a Hypercube build in the works for a while now, so I just raided what I needed from that.)I printed the plastic bits in eSun solid-purple PETG: https://amzn.to/3cndPrqSome signficant differences between the stock A8 (or AM8) and...

Tis is my project in 3ds max 2013 on Main towers, more is here http://www.skyscrapercity.com/showthread.php?t=1577513

build

build

build

build

http://www.thingiverse.com/apps/customizer/run?thing_id=48198 Instructions Using the following options: text = Build It Workshop split_band = no Width = 5 letters_inside = no text_font = write/orbitron.dxf Height = 10 band_OD_percent = 70...

Wanted to do a virtual build in CAD, but have it look real. This is everything I used to make mine in 1 file. In this kit you will find all of the "C" mpcnc parts as well as the hardware and a belt section to get you started. This kit is intended for...

I've been trying to come up with a heavy duty rack to store my filament rolls that is built well and doesn't break the bank. Today I found a solution that I love and I wanted to share it here on Thingiverse. My solution was assembling a rack made...

I've been trying to come up with a heavy duty rack to store my filament rolls that is built well and doesn't break the bank. Today I found a solution that I love and I wanted to share it here on Thingiverse. My solution was assembling a rack made...

This is my version 1 for 15mm x 30mm oval aluminium tubes. Check for my version 2 (better) of this thing. ...http://www.thingiverse.com/thing:1063923

This is my version 2 (and a lot better) of previous connectors for 15mm x 30mm oval aluminium tubes. ...This has better support for the aluminium and slight bigger holes for screws (version 1 tent to crack when screwing).

<h3>Halter für 9 Druckplatten.</h3> Maße: 250 x 67 mm, 60 mm hoch Die Zwischenräume für die Druckplatten sind 3 mm breit. Ich benutze 1,5 mm FR4 Platten mit Magnetfolie das sind insgesamt 2,2 mm Die größte Druckplatte auf den Bildern ist...

When I decided to build a quadcopter, I decided after a couple of decades of putting it off, and sticking to 2D CAD, to try and learn 3d modelling and build a virtual copter too... This is my first go... a few evening of watching YouTube video's and...