build plate holder 3d models

Introducing the replacement Rep 2 build plate holder - and it's uniquely printable on your trusty Rep 2 right out of the box! When designing this critical part, I encountered a unique challenge. Due to its thin wall structure, additional support...

Made a quick build plate holder for the Elegoo Saturn. Can be placed diagonally downwards or upwards depending how big the print is. ... Not perfect but hope it helps.

Build Plate holder that allows for better drainage for Anycubic M3 Plus.  This is my first version remixed from https://www.thingiverse.com/thing:4721128WARNING: THIS HOLDER IS TOO TALL for MAXIMUM HEIGHT, REMOVE IF YOU ARE MAKING A TALL PRINT...

Build plate holder for the Form 1 printer to aid in print removal. The supplied accessory kit for the Form 1 is insufficient to hold the plate steady when removing parts after printing. This holder can be screwed to the workbench for added stability....

Clip for mounting a 2.3mm glass plate on the RigidBot build plate (7mm gap).

This means if you print the 4 plate holder then decide you need two more plates, you can print a 2 plate holder and tie them together with the connector and some m3 countersunk screws.The second benefit is how it staggers and offsets the plate. One...

Clamp designed specifically for securing a 2.3mm thick glass substrate onto the rigid build plate of an RigidBot setup, featuring a consistent 7mm clearance.

build plate holderI've mounted it on the aluminum profiles, but it's also fine under the desk or on the wall, etc

A Compact yet Effective Overhaul of the AC Photon Resin Saver. ...The Build Plate is Angled at a Precise 45 Degrees to Efficiently Drain Excess Resin Back into the Storage Vat.

The holder for the second printing plate, I didn't like any I've seen for download so I drew my own. ...The model is easy to print without supports, for a layer thickness of 0.2 mm, I glued each side with two pieces of double-sided tape and then screwed...

Easy holder for my buildplate - compatible with buildplate for Elegoo mars 2 Pro ( i dont sure if compatible with mars3 - i test in future ) This holder fit to plastic boxes from Kaufland store in my region. ...Boxes dimension 22x14x12cm volume 2L ...

... ...Next version work in progress with an higher stem. Do not waste even a drop of resin! The holder has his own direction, because he has a gentle slope in order to collect the resin inside of the jar: follow the picture above to use it. ...Enjoy

... shaft. Don't let even a single drop of resin go to waste! The holder features its own orientation, thanks to a subtle incline that enables effortless collection within the jar; refer to the accompanying image for proper use and enjoy the results.

V1 build plate holder for Anycubic M3 Plus.

Bambu Lab wall mounted build plate holder. ...Can hold up to 4 plates.

Wall-Mount Build Plate Holder for Photon Mono XHave fun with it.

Build plate holder for my Voron V0.1. ... Printed in ABS and glued together with acetone (or super glue).

Older build plate holders (with a basic right-angle design) would bend and eventually snap. This design, while basic, has been working great for several months. Not much more to say really. It does what it says. * Updated due to being giant...

Found the Build Plate, Sheet holder for the Mk3S. ...I have reduced the X-lenght to 205mm does fit perfect for the Mini plates

This is a straightforward revision of the Phrozen Transform build plate holder, which readjusts the hook further towards the center of the build plate to prevent resin from dripping onto the handles and sides of the FEP vat.

This is a build plate holder that allows you to remove remaining resin after printing Halot Mage Pro. ... Making Blog Post https://www.soonsoon.io/creality-halot-mage-pro-plate-holder/ Contact soonsoon@soonsoons.com

Rapid Prototype Build Plate Holder. Crafted with precision using Fusion's powerful design tools and manufactured with PETG on the Ender 3 FFF printer. ...Employing a 0.2 mm layer thickness, three robust walls, and an optimal 20% infill density for...

A simple build plate holder for the Anycubic Photon Mono printer that allows for the resin to drip off the plate a bit easier after a print is done.I used to use another one I found on the internet but its angle was too big so the taller prints were...

Human: Build Plate Holder for SparkMaker FHD===================================== This utility is designed to hold your build plate securely while dripping resin or cleaning, eliminating the need to place it on a table. A spring-loaded head allows...

Build Plate Holder for SparkMaker FHD===================================== This utility is designed to hold your build plate securely while dripping resin or cleaning, eliminating the need to place it on a table. A spring-loaded head allows for easy...

This is a version of my regular Mars 3 build plate holder that uses a magnetic mount instead of the 2020 extrusion mount.  Compatible MachinesMars 3Mars 2/2 Pro (Im 95% certain its the same mount as the 3, but I am awaiting...

I needed a holder for my Prusa Mini build plates and spare usb drives so I quickly designed this in Fusion360. Will hold up to 4 build plates and 2 usb drives. Super easy to print and should be able to print without supports. ...Printed with Prusament...

Built to hold 2 build plates for the AnkerMake M5 printer. ...This is a first try and I plan on adding some accessory holders for other projects and nozzles

I wanted a way to support the build plate so I could use both hands to better place the flex plate onto the magnet. The support legs are tall enough to accommodate the build plate screw being turned all the way out. Although the legs can be...

I designed these to securely hold my polycarbonate build plate atop my Robo3D R1+ glass plate without hindering the movement of lower Z-axis components, due to clips and dual fans. This design is intended to fit under the glass bed over the bump...