bump to bar 3d models
2195083 3d models found related to bump to bar.grabcad
Often the hook would snap or even wear right through, either allowing the expensive bump-bar to drop to the ground or hang precariously on a "stump".When I'm not in the kitchen I'm at university studying Mechanical Engineering and always looking for...
thingiverse
Lathe truing bar for making part in chuck concentric to chuck. designed as a 5/8 tool, using a "1614" bearing that is 1.125" OD x .375" ID x .375" thick. Assembly built with Mcmaster carr parts. ...Two variations with purchased / fabricated metal spacer...
thingiverse
A fake camera bump to prevent the phone from rocking when it lays on a table
thingiverse
Here is a shorter Skid plate to clear my bump box. This should fit MBX5 or 6. Maybe 7 or 8. ... Favorite Fuel ...
grabcad
Hello,Here by this project, we just tried to see if it was possible to put this furniture here, eventually we didn't!
thingiverse
just a bit of fun i'm not in gone to the bar ..........pub at 100% back is 4mm thick and text is 2mm if you like this or any other of my designs ( enter awelshman in the search box ) please feel free to click the like button thanks
thingiverse
This is a box that you can slide a matrix leadscrew square nut into and then attach 2 tetrix angle bars onto.
thingiverse
Customized version of http://www.thingiverse.com/thing:56795 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:56795 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=56795
thingiverse
Customized version of http://www.thingiverse.com/thing:52761 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=52761 Instructions Using the following options:...
cults3d
Play a classic game of dominoes or construct and topple a domino design with the Bump Dominoes. ...Includes 28 dominoes to create a complete double-six set.
thingiverse
A bump that attaches to a corner in my desk so I don't scrape my knee every time I sit down.
thingiverse
Mr Men - Mr Bump To have colour change, pause and manually change colour, else need to remix to split design for multiple colour extruders. ... Eyes and mouth coloured in with black sharpie.
thingiverse
Hello, Here is a small bridge for rallyman to decorate the "bump" sections. With this, your rally cars will make huge jumps, but watch out for loss of control! Scale 1/220. ... Good games to all.
thingiverse
... run past,.... ...and occasionally fall. Just to be sure they do not fall on the corner I made a generic corner bump cap. Easy to glue or tape on with double sided tape. Can also be used indoors.. obviously. ... Maybe it comes in handy for you to.
grabcad
traffic bump looks fantastic for hotels ,clubs,airports and general places. ...
cults3d
... for Ti-lite wheelchairs and assists in holding the individuals foot from kicking forward and falling off the foot plate. ...It also protects people in wheelchairs from bumping their feet into anything that may cause serious injuries. ...Patent Pending.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52761 Instructions Using the following options: keyheaddiameter = [25,20] keybladelength = [28.50,18.50] topslotheight = [3.50,3.50] keycylindercount = [5,4] keytiptopyoffset =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: keytipbotyoffset = [key_bslot_yoffset,(blade_height/2),0.00] topslotangle = [30,30,0.00] keytipbotangle = [225,225,0.00] backslotangle =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: keyringradius = [4.5,4.0,4.0] frontslotzoffset = [(5cyl_front_slot_layerslayer_thickness),0.00,0.00] topslotangle = [30,30,0.00] backslotzoffset =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: keyringradius = [4.5,4.0,4.0] cylinder_z_rotation = [0,45,0,45,0,45,0,45] straightlength = [27,22,0.00] safe_pin_xoffset =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: backslotyoffset = [key_fslot_yoffset+key_fslot_height+0.50,1.00,0.00] straightlength = [27,22,0.00] keyheaddiameter = [26,20,0] backslotzoffset =...