butane torch adapter 3d models

Simple stand for butane torch that attaches to an 8oz (227g) or 8.8oz (250g) butane canister. Without the stand the torch tends to be front-heavy and tips over easily. By adding the stand everything is nice and solid. Can should be a snug fit in the...

... is nice and solid. Can should be a snug fit in the base without any post processing. The pictured torch is a [Ypres SU Professional Butane Cooking Torch](https://www.amazon.com/Ypres-Professional-Soldering-Jewelry（Butane-included）/dp/B0786JZHSR)

https://www.bedbathandbeyond.com/store/product/bonjour-chef-s-tools-butane-culinary-creme-brulee-torch/1013057451?keyword=butane This is the second part of this lighter I have replaced. ...See https://www.thingiverse.com/thing:5551698 for the flame...

Simple stand for butane torch that attaches to an 8oz butane canister Without the base the torch tends to tips over easily. cylinder should be a snug fit in the base without any post processing. ... This should most cylinders of this type/size.

Needed a replacement base for my butane torch, but could not find a suitable one (or one that would fit) my "Scorch Torch". The torch is just under 52mm wide at the lip found at the bottom of the torch. So I designed this base to be as SNUG as...

An egg-shaped base replacement for the Bernzomatic ST2200T butane micro torch. The base has a stouter shape than the original and a better replacement if you lost yours as I did. The base is designed to have a perfect friction fit and an opening to...

An egg-shaped base replacement for the Bernzomatic ST2200T butane micro torch. The base has a stouter shape than the original and a better replacement if you lost yours as I did. The base is designed to have a perfect friction fit and an opening to...

I created this support for my little kitchen torch that does not stand up well.

3d model torch, there is 3d model of the flames too , project file blender , with and wityhout subdsurface, any question contact me, thank you

Broke my Snap on torch base (no pun intended) so I needed a replacement to reduce tip overs. ...Print Settings Printer: Tevo Tarantula Rafts: ...

This is an adapter for a Butane Fuel Canister to fit lighters. It can be printed on a FDM printer or a SLA (Resin) printer. If printed by FDM, use 0.1mm Layer height and a Brim (Brim only on Outside ☑) There is a long (10mm shaft) and a short...

Simple Standn for 2000-01 VersaTi Precision Butane Torch

Gridfinity Butane torch holder is a 1 x 3 with standard magnet slots

Butane torch stand For my daddy, 120mm size, 8 grooves for easy to check the 45º edge

Safety Delete clip for Medicali butane torch so you do not have to pull the pin down while you press the trigger to make it a one handed task. ...Pretty niche, ill be surprised if I get any downloads lol.

Love the [Eagle Tech butane jet torch](https://www.amazon.com/Eagle-Lighter-Adjustable-Windproof-Refillable/dp/B0159G9LG8/ref=sr_1_6?dchild=1&keywords=Eagle+Tech+Torch&qid=1621910102&sr=8-6) but hate how it is constantly falling over. This stand is...

This nozzle adapter can be used to fill Butane Jet Lighters or Disposable Lighters using standard Butane Gas Canister Nozzle Use butane torch to heat the nozzle fitting side of the adapter then insert, it will create an airtight seal and you'll not...

This nozzle adapter can be used to fill Butane Jet Lighters or Disposable Lighters using standard Butane Gas Canister Nozzle Use butane torch to heat the nozzle fitting side of the adapter then insert, it will create an airtight seal and you'll not...

This adapter will adapt between a Sterno butane fuel cartridge and a little port on a creme brulee torch, once you can take off the cover to give it a little more space to squeeze in. ...Remember to hold it upside down so the liquid will travel into...

The adapters/nozzles that came with the can of butane never fit my lighters quite right, so I made my own. I had the best results when they were printed with a 0.25mm nozzle. Note that there are different files for PLA and TPU. They have slightly...

This is a replacement base for the refillable Bernzomatic ST2200T Butane Micro Torch. The original base broke off my torch after a fall, so I designed this to be a replacement. ...It fits snugly against the rubber hand grip, so no glue or screws are...

The E-Tek 89960W is a small, inexpensive (<$15) butane torch carried at Walmart stores. This printable model securely attaches to the bottom of the torch with 1-2 dabs of hot glue and provides a stable base suitable for hands-free use. Includes a...

see my file "Thermacell_Filler_v1" I would label this version as obsolete as the newer version is a stand-alone unit that utilizes the gasket on the cartridge this is an adapter for a standard butane tank to fill up thermacell cartridges. It isn't...

Small holder used to store the Iwatani CB-TC-PRO Butane Torch onto the base of the stand. Printed with ABS and used acetone to fuse the two parts together. Alternatively you could use any adhesive that works with your print material. ...M3 screw and...

Slip on belt to hold filling adapters.Filament: TPULayer: 0.2 mm&nbsp;

I have a bunch of butane cans for an old Campmate camping stove to go through before I upgrade the stove itself. But the plastic adapter from the can to the stove tube broke, so I made this replacement. ...

Athough a stand comes with the Iwatani torch, which by itself works quite well to stabilize the butane canister while the torch is attached, disassembled it can only hold either the butane canister or the torch alone, and not both. Such a setup...

<p><strong>Donate if you're pleased with my work i'll appreciate it!</strong></p><p><strong>Every donated buck will be spended for printing materials and hardware.</strong></p>

Nozzle only.

Nice and tight fit. ... ------------ **All content (models and everything created by me) on my page is under WTFPL license (Do What the Fuck You Want - http://www.wtfpl.net/) but if you pleased with my work and i helped you you can donate (or not) me...