c64 case 3d models

... slight lip to aid correct alignment of the hinge so that it will connect with the bottom half of the case. I used hot glue and seem to have adequate results. All credit goes to the original designer of the C64 case hinge LeftoverBeefcake . ...

... my case. I made this with a printable gauge. The tab has to be just the right height to fit in the case groove. It also can NOT extend over 1/2 the case thickness. Or it will not fit and may break your case. ... These are for C64 BreadBox design.

Standard sized C64 cartridge case. Shows up great in black. ...You need a screw to close it.

Commodore 64 and 128 Cartridge CaseBased on drawings at wiki.icomp.de/wiki/C64_Cartridge_Cases.These housings can be ordered at icomp.de/shop-icomp/de/shop/product/c64-cartridge-cases.html. I recently ordered some for a small project and checked out...

A fix for Cracked/Broken screw holes for Commodere 64 Breadbin Case ( C64). ... Clip de broken parts and glue the new part onto the remainings and set to correct hight

Simple case to be used with the BWACK C64 saver 2.1 https://github.com/bwack/C64-Saver-bwack Cable Clamps used RS PRO, Black Nylon 66, Strain Relief Cable Bush, 7.4mm Bundle Diameter P/N 817-8861 4 core 20awg cable diameter 5mm screws for the top 3mm...

Simple case to be used with the BWACK C64 saver 2.1 https://github.com/bwack/C64-Saver-bwack Cable Clamps used RS PRO, Black Nylon 66, Strain Relief Cable Bush, 7.4mm Bundle Diameter P/N 817-8861 4 core 20awg cable diameter 5mm screws for the top 3mm...

Simple case to be used with the BWACK C64 saver 2.1 https://github.com/bwack/C64-Saver-bwack Cable Clamps used RS PRO, Black Nylon 66, Strain Relief Cable Bush, 7.4mm Bundle Diameter P/N 817-8861 4 core 20awg cable diameter 5mm screws for the top 3mm...

DIY Case for the Commodore 64 shortboards that is easy to assemble and disassemble. ...It serves the most during tests and before the motherboard ends up in the original case. ... Video: https://youtu.be/ZTbPVGmvT14

This is an alternative case for the SD2EIC with Browser. It has two buttons on top and one on each side. The board can be found on PCBWay. Cable comes out left side. I purchased it on Ebay. ... ...

Motherboard standoffs to replace cracked, broken or missing standoffs in the bottom of the breadbin cases. I made them extra wide on the bottoms for enough glue to surface contact. Sand down what is left of the broken standoffs. Screw the new...

I wanted a version of banman's design that fit between the vertical supports of my machine, as I'd prefer to limit grinding and modifications to the case. So I just resized banman's model to 14.5mm wide and manually tweaked the fit using scissors...

I wanted a version of banman's design that fit between the vertical supports of my machine, as I'd prefer to limit grinding and modifications to the case. So I just resized banman's model to 14.5mm wide and manually tweaked the fit using scissors...

Design changed to fit with different cartridge desing. ... Holes are made for inserts for m3 screws.

This beautiful C64 case top has been modified for sleekness and some heat ventilation.

Wanted a case for my VersaZif64 Cartridge and did not find one, so I made one. ... This is a remix of outrun69's awesome C64 Cartridge Case Best to print upright with supports for strength of cart half clips

Commodore C64 - UK1541 Case

simple case for the Kernal Card made by Faszination C64

case for XUM1541-II https://www.pcbway.com/project/shareproject/C64_XUM1541_II.html

This is a case for bwack's C64 saver version 2 https://github.com/bwack/C64-Saver-bwack The design includes a strain relief for each cable. The strain relief has to be printed twice. ... The design is made in Fusion 360 (design file included) and the...

Case for a C64 joystick port switcher like this one: https://www.polyplay.xyz/Joystick-Port-Umschalter-Commodore-64 If you need to modify anything: https://www.tinkercad.com/things/8EMEezukQ8W

... photo shows the case printed in eSun PLA+ Bone White, it matches quite well with the color of the Commodore 64 and VIC20. Link to the Sordan.ie SD2IEC adaptor https://sordan.ie/product/719/sd2iec-adapter-sd-reader-for-commodore-c64-c64c-c64g-vic20/

I liked the case that was already up here for the WiModem but I decided I wanted something a little more flashy for my C64. I designed this case for it that has interchangeable face plates so you could make to your liking. I have included three...

I liked the case that was already up here for the WiModem but I decided I wanted something a little more flashy for my C64. I designed this case for it that has interchangeable face plates so you could make to your liking. I have included three...

I liked the case that was already up here for the WiModem but I decided I wanted something a little more flashy for my C64. I designed this case for it that has interchangeable face plates so you could make to your liking. I have included three...

I liked the case that was already up here for the WiModem but I decided I wanted something a little more flashy for my C64. I designed this case for it that has interchangeable face plates so you could make to your liking. I have included three...

I designed this case for it that has interchangeable face plates so you could make to your liking.I have included three face plate designs in the files and I have printed and painted two as an example. The face plates were painted after printing but...

I just glued the side closest to the C64 case and left the other side to snap into place. I'm new to this, so forgive me if this isn't great. Print Settings Printer: Wanhao Duplicator i3 ...

This is a case for Bwack's modular [C64 Saver v2](https://github.com/bwack/C64-Saver-bwack). ...See [my blog post](https://www.hackup.net/?p=2480&preview=true) on this build for more details.

This is a case for Bwack's modular C64 Saver v2. ...See <a href="https://www.hackup.net/?p=2480&amp;preview=true">my blog post</a> on this build for more details.</p> Category: Electronics