c64 user port 3d models
87520 3d models found related to c64 user port.thingiverse
This is an user port module case for C64. It is not perfect, bit it will fit. It has an opening for 2 LEDs and for a USB port. ...Print Settings Printer: A8 ...
thingiverse
This is a remake of the classic caps for user port board-edge connectors of the Commodore home computers. Each cap consist of a top and a bottom part with additional mounting holes. There are three variants with different openings for the cable: to...
prusaprinters
This is a remake of the classic caps for user port board-edge connectors of the Commodore home computers. Each cap consist of a top and a bottom part with additional mounting holes. ...There are four variants with different openings for the cable: to...
thingiverse
I/O trim plate to for the user port area of Commodore 64 using the Ultimate 64 main board. This slides into the case before sliding the board into it. No modifications or screws needed to hold it into place. I have version 1.2 of the U64, I think...
thingiverse
These inserts can be used to key edge connectors like those required on the user port or cassette port of the Commodore 64. Properly keyed connectors will fit the correct way only and can no longer be reversed accidentally. The dimensions of...
thingiverse
The case parts have also texts "THIS SIDE UP" and "THIS SIDE DOWN", because great harm and smoke can occur if inserting a user port cart upside down. ...Firmware:https://github.com/jsalin/esp8266_modem Video: https://www.youtube.com/watch?v=oiP5Clx3D_s
prusaprinters
These inserts can be used to key edge connectors like those required on the user port or cassette port of the Commodore 64. Properly keyed connectors will fit the correct way only and can no longer be reversed accidentally.</p><p>The dimensions of...
thingiverse
... fit this housing. I have done this based on the Wemos D1 mini (ESP8266), but others can be used as well. The case offers a slot to fit the standard User Port connector exactly, so the plugging and unplugging loads do not go onto the PCB connection.
thingiverse
Cover for C64 User Port (24 pin) / Cassette Port (12 pin) connectors. ... Connector I used: https://www.aliexpress.com/item/Sample-2pcs-Lot-805-Card-Edge-Connector-3-96mm-Pitch-2x6-Row-12-Pin-PCB-Slot/32539449444.html ...
prusaprinters
Cover for C64 User Port (24 pin) / Cassette Port (12 pin) connectors. Connector I used: https://www.aliexpress.com/item/Sample-2pcs-Lot-805-Card-Edge-Connector-3-96mm-Pitch-2x6-Row-12-Pin-PCB-Slot/32539449444.html...
thingiverse
I wanted to put SidFX switches, audio out and rom switcher switch in my commodore 64 without drilling holes.This cover goes to the user port as I don´t have any use for it. The cover mounts below the motherboard and it also covers user port pins so...
grabcad
This is a model of the PCB mounted metal cover of the C64 expansion port (also C128)
myminifactory
... ...My original blank keys are here https://www.myminifactory.com/object/3d-print-commodore64-replacement-blank-keycaps-109077 These few are for users to test if their printer can handle the resolution needed especially the face PETSCII characters.
thingiverse
The plug was designed to protect the C64 from dust ingress and to protect the user port connector from mechanical damage. It snaps on to the plastic case, and does not touch the 24 pin user port connector or the motherboard. Tested working with...
thingiverse
https://www.sidfx.dk/ Print this cover, slide both switches and the audio jack through from the inside and press the cover onto your Cassette-Port from the outside. Be gentle, the tabs are very brittle. ... It's a snug fit, but worked fine on a C64C
thingiverse
There are also JIFFYDOS caps for the F keys at https://www.thingiverse.com/thing:4705417 Designed using Illustrator, Paint dot net, and Fusion360, I am working on a set of C64 keycaps (edit: full set is now available. link is farther down) . My...
thingiverse
Semplice organizer per schede user-port per computer Commodore 64 o Commodore128
thingiverse
Simple cases for the user and cassette port edge connectors for vintage Commodore 8-bit computers (including Commodore PET, VIC-20, C64, C64c, C128 and the Plus/4, C16, SX-64 minus the cassette port). You'll need two small screws to attach the...
thingiverse
... on top of the cake" Please do not sell printed copies of this model to make a quick buck out of it as has happened in the past with some of my designs. Appreciate the work spent to design this model and keep the community alive! C64 Rulez!!! ...
thingiverse
... inside the C64 case. This mount slides over the cassette port interface and provides a slot that holds the SD2IEC in place inside. ...You still need to solder leads to the appropriate locations on your C64 motherboard to provide power and data.
thingiverse
Edge PCB connector of 6 pins for the Commodore 64 tape interface. ... v3 is just the pcb edge 6 pins v5 has some width correction plus the side slot Datasette connector
thingiverse
Cover for the 9pin Joystick ports on the C64. Could glue in bit of antistatic foam for tighter fit if needed. I tested this on a C64 breadbin and the Ultimate64. ...
thingiverse
Commodore 64C User port cover for STRIKE LINK Wireless card. ... Printed on a Creality 3D resin printer, it does not need supports if the printer is well calibrated.
cults3d
... Bear Industries is selling these prints for $15! https://www.laserbear.net/products/snes-user-port-adapter-case-for-commodore-8-bit-computers Adapters can be purchased separately from TexElec at https://texelec.com/product/snes-adapter-commodore/.
thingiverse
... is selling these prints for $15! https://laserbear.net/shop/ols/products/snes-user-port-adapter-case-for-commodore-8-bit-computers Adapters can be purchased separately from TexElec at https://texelec.com/product/snes-adapter-commodore/. ...
thingiverse
A replacement port cover plate for the The C64 and the The VIC 20, with a very unassuming power button, and a hole for a 3.5mm stereo jack for a console (serial) port. ... This prints as one object, including the button.