cable chain brackets for printrbot classic 3d models

This is a custom extruder mount designed specifically for the HyperCube Evolution, featuring a secure attachment point for a cable chain end. ...The cable chain end in question is sourced from a popular open-source design found on Thingiverse,...

Open Cable Chain End for Geeetech Pro B I3 8mm Find Open Cable Chain here : http://www.thingiverse.com/thing:611593 Print Settings Printer Brand: RepRap Printer: Prussa I3 Geetech proB Rafts: No Supports: Yes Resolution: 0.3 mm Nozzle - 0.15 mm Layer...

This is a modification of cable chain that enables seamless connection between the chain and the heat bed. Check out this link for more information: https://www.thingiverse.com/thing:3769941. ... It fits perfectly over the original cable cap, requiring...

Designed this from https://www.thingiverse.com/thing:4794723 I wanted the chain to extend to my direct drive for cable management. It uses the chains from https://www.thingiverse.com/thing:376994 I do recommend tree supports, clean them off and...

I created this cable chain ad connectors for my IndexPnP that I am building. ... The Link and LinkCovers is a remix of an existing cable chain that I have increased the size to 180% The connectors/mount points were done in Fusion360.

Here are the files needed to integrate "Ultimaker2 Cable Chain" by sneakypoo into a modified Cubepro printer without requiring any drilling or machining. This will allow you to properly manage hotbed cables. The parts were designed to match the cable...

The chosen cable chain measures 14mm in width and 10mm in thickness. For a comprehensive rebuild, refer to thing 2079048 on thingiverse. ... Additionally, consider exploring thing 2170271 for an enhanced design that incorporates an IR Probe housing.

Remix of [Ender 3 Cable Chain Extruder Mount](https://www.thingiverse.com/thing:4592642) for [Ender 3 Cable Chain, no screws, no unplug cable](https://www.thingiverse.com/thing:3769941). It's going to need supports, but you can decide which direction...

This is a remix of ijohansson's "CR-10S Pro v2 cable chain with 90 degree brackets" but it is designed for the slightly narrower ribbon cable on the version 1 printer which I have. ijohansson's version is a remix of "CR-10S PRO side Cable Chain" by...

Good morning, sir, Pack including all the elements to make a cable carrier chain for the Y-axis of the CREALITY ENDER 3 or 3-PRO printer. Easy to install, the chain is fixed in the grooves of the aluminium profile for the holder and takes up the...

### Cable Chain Adapter Mounts for Ender 3 Pro Quick and dirty mod to make the chain bottom_connector for Ender 3 v2 fit an Ender 3 Pro: https://www.thingiverse.com/thing:4932649/files Larger bed connector worked for Ender 3 Pro:...

Add holes to the controller end part of the cable chain to secure wires and provide strain relief with a cable tie. Mounting occurs at a slight angle due to misaligned holes in the bed and control unit box, but the setup still functions. Adding...

NEW UPGRADE Z MOUNT - prefect fit This is a remix of the cable management chain for the Elegoo Neptune 3 PRO printer. -------------------------------------------------------------------------------------------------------------- I recommend...

This a remix for the Cable Chain Hotend originally made by MichaW for his project. ... I made this remix with closed attachments to make it more stable and fixed to the x axis wheels.

I'm planning to create a straightforward cable chain mount for my MendelMax, built specifically with Misumi 2020 extrusions in mind and featuring an M5 T-slot nut. This setup should easily fit any variation of RotoScan's Cable Chain (available on...

Cable chain mount I designed to work with fantasmag0ria's Modular X-carriage.

So I modified the design by wku_wake for a ender 3 V2 chain mount and modified it slightly to fit the other chain design Update: Added flipped version as per community requestm, also added the files for the end bits if you want to use the chain for...

I installed Starwhooper's Improved Linear Chain to Extruder and davbarr's Z_Motor_Fixation_Chain for Anet A8, both from thingiverse. Like many users, the chain would pop out of the z-axis mount and curve upwards, failing to stay flat and parallel...

This is an upgraded version of the cable-chain end for the X-Axis. ...Remove two screws from the extruder NEMA stepper motor, insert the clip into position, and reattach the screws.

Here are some custom cable chain ends I designed for my Tevo Tarantula, and they function flawlessly - I'm compelled to share them with fellow enthusiasts. Hopefully, you'll find them useful too. ...http://www.thingiverse.com/thing:11978

If you previously inserted the M3 nuts into the designated areas for future upgrades, you can utilize them as a precautionary measure if your Vertical Cable Chain components fail and snap off.

Ultimate cable chain with mounts for bed and extruder and everything.   Credit to johnniewhiskey on Thingiverse: https://www.thingiverse.com/thing:2920060

it is still little bit difficult to print but works ok with supports For the chains and adapter to the heatbed just use the same as for the MK2. see here: https://shop.prusa3d.com/forum/improvements-f14/mk2-cable-chains-t1538.html#p33758 i just mixed...

This is a custom end mount that I designed specifically for tosjduenfs' cable chain system. It features two #6 machine screws that securely attach it to my bed mount plate, neatly guiding my heat bed and thermistor wires out of harm's way. I've...

This support is designed specifically for the Cable Chain of ModelStation, which can be found on Thingiverse as item number 11978. The support can be attached securely to the ends of the cable chain using M3 screws. ...Additionally, it features a...

Update: Corrected flawed nut recess installation.\nInstalled mounts with no recess.\nI required a longer cable chain to facilitate conversion from standard wiring to CAT-6 and allow for excess wires.\nThe chain can accommodate 4 CAT-6 cables and one...

I designed a support system for my cable-driven 3D printer's tornado. I converted it into a direct drive setup, which allowed me to repurpose the original extruder mount to secure the holder in place. This ensures that the chain moves synchronously...

Realised after printing out the cable chain https://www.thingiverse.com/thing:3769941 that it was for a Ender 3 Pro, rather than the Ender 2 v2 (which mounts the power supply where the original chain would connect), and then found this chain that...

Here are the materials needed: 4 screws, M3 x 7mm 2 screws, M4 x 10mm Tap for M3 screw Drill bit, 2.5 mm (for tap) Heat-shrink tubing Result: A sturdy bed cable chain that will keep your Prusa i4 running smoothly. Print Settings: Printer: Prusa i4...

Check out this thread for more details: https://shop.prusa3d.com/forum/improvements-f14/mk2-cable-chains-t1538.html#p33758 This design combines the files from Prusa with Aaron Yourk's work, which you can access here:...