cable end maker 3d models
238586 3d models found related to cable end maker.thingiverse
Assembly video: https://vid.me/Kwxf Ribbon cable version: http://www.thingiverse.com/thing:1107461 Ever wish you could have some nice orderly data cables for your arduino projects without paying a surprisingly large amount for crimpers, sockets, and...
grabcad
High end coaxial compression fitting for cable tv and internet. ...Fits on the end of the coax cable.
thingiverse
Customizable OpenSCAD file to design your own End Cap for your Cable Duct.
thingiverse
flexible end of calor iron cable to print in TPU95A embout souple de cable de fer a repasser calor a imprimer en TPU95A
thingiverse
created some new end parts for this cable chain. ...Thank you for the original design, works very well.
thingiverse
Here is my design for iPhone Cable End Supports. ...I was sick of the cable always fraying and snapping so I designed these supports to give a little more strength.
thingiverse
Cable Chain End With 6mm bore. ...Print Settings Printer Brand: RepRap Printer: Home Made printer ...
thingiverse
I wanted a more secure way of attaching the cable chain to the hot end of my printer. ...so i designed a part that will work with the bent part of the hot end
thingiverse
One piece Switch Housing for cable end switches. Print the housing on the small surface where the cable exit and you need no support. Raft is recommended in case the bottom surface is pretty small. ... Print and measure before you buy the switch and the...
thingiverse
... on my bedside table. This is useful as, at night, after I have turned my phone off, I am able to find the cable-end easily in the dark. ... Required for assembly 2 screws - Unsure of Size, approximately M3 bolt-sized Thank you matthewlim.ml
thingiverse
Designed this to replace a string hanging from the top of my delta printer holding the end effector cables up as the electronics are installed under the print bed. Just print and install to the bottom vertical profile and push the cable to the...
thingiverse
this is a usb cable end organizer/holder that secures to a 3/4 thick table via a screw in the holder. but u can easily modify it to fit other table thickness. the cord is secured by the fact that the cord is squeezed a tiny bit t o go into the...
thingiverse
End of the cable chain to mount to the frame. The two holes are for M3 screws and are 27mm apart. If anybody needs a 90° angle i could create that as well, just comment below. ... Print Settings Printer: Tronxy 3DCSTAR P802 ...
cults3d
Oh no, you broke the ethernet clip tab! ... I have the solution to your problem:D a small tip to put on your male ethernet cable is your worries fly away! Oh too strong Predor! ... (Small precision the surface must be flat on the male end)
thingiverse
Cable chain end with cable holder, two fixing holes for DIN 912 M2.5 mm., printed in PLA, 100% infill, supports, the Gcode attached is for an Artillery X1 with this adjustments, Solidworks editable part file attached too. Peace! ...
thingiverse
I removed the wastebasket and use the screws from that to mount the new end piece. I would like to thank Doudou14 for posting his version of the cable chain, it works perfectly. ...Updated 4/11/16: Extended the front to eliminate 3 segments and now...
prusaprinters
... than I did on this print, as the clasps that hold the two pieces together can be a little stiff if you don't. ...You might also want to apply a small dab of superglue to the end of the flexible cord guard to keep it connected to the cable. Enjoy!
prusaprinters
flexible end of calor iron cable to print in TPU95A embout souple de cable de fer a repasser calor a imprimer en TPU95A Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 0.2 Infill: 20% Filament: polymaker...
thingiverse
After printing my own cable chain and getting disappointed with the results, I broke down and bought some Igus cable chain. It's pricey but you know what - you get what you pay for. I made this little end piece that fits into the hole in the sheet...
thingiverse
The little thingies to keep your bike derailleur and brake cable from fraying. ...Just slide them on your cable a crimp with pliers
youmagine
This two pieces are for hide wires and connect cable chains. ...This is derived fromhttp://www.thingiverse.com/thing:57533
myminifactory
Cable chain link with a hole for attaching to aluminum extrusion. I'm using this for my heated bed cable. ...The chain in the picture is this one: 10x10mm drag chain* Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black...
cults3d
Cable chain link with a hole for attaching to aluminum extrusion. I'm using this for my heated bed cable. ... The chain in the picture is this one: 10x10mm drag chain* Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black...
thingiverse
The 1/16" steel cable on my car door latch had elongated making opening the door impossible. I created this part to effectively shorten the usable length of the cable. It uses a 3M screw, nylon bolt and a locking washer to secure it to the steel...
thingiverse
Add a slide-in to secure the body and shell, also locks the RJ45, and the rear can be reinforced with a cable tie. ... 2022-01-29 V2 Add left, right version and
thingiverse
This two pieces are for hide wires and connect cable chains. ...This is derived from http://www.thingiverse.com/thing:57533 Instructions This is derived from http://www.thingiverse.com/thing:57533
thingiverse
This is a remix of a remix. ...The original can be found here: https://www.thingiverse.com/thing:4647606 This is just a modified end link for the chain so that the end is flat. ...You will still need the chain link cover file from the original remix.