cable loom 3d models
94033 3d models found related to cable loom.thingiverse
This is basically just a Y splitter for Cable loom (the plastic split wire protection stuff. It takes 3 heat set M3 inserts and 3 M3 bolts. Print Settings Printer Brand: LulzBot ...
prusaprinters
It takes 3 heat set M3 inserts and 3 M3 bolts. Print instructionsUnassociated tags: Aquarium Tubing, cable loom, wire harness, wire loom, y splitter Category: 3D Printer Parts Summary This is basically just a Y splitter for Cable loom (the plastic...
thingiverse
This is a simple clip to hold split-loom for wires and cables. ...It has a tab on it to allow for a push-pin to go through it, but another tab to ensure that the loom doesn't move.
thingiverse
Got sick of the cable loom flopping around - I left this upstand generic so that other things could be attached to it if required. Oh, ignore the nimble on top - was just my future configuration once I get everything done... ...currently it is...
thingiverse
Inspired by https://www.thingiverse.com/thing:4601401, I created this cable loom holder that screws in with M3 screws and T-Nuts on the inside of the 2020 extrusion bar. ... You can add an extra zip tie if you want as well.
thingiverse
So I thought I would make a couple of wire looms to use, not just for the printer build but also for a few ARDUINO projects I am planning. After making my first print I decided to make some other sizes so I thought a CUSTOMIZER THING file would be...
thingiverse
Goes in to existing screw hole supplied for holding loom with cable tie. ...Eases the wear on the loom during movement.
myminifactory
The stepper motors are now covered and the cable loom is supported. Minimal support is required if printed with the cable entry hole on the bottom. Will fit on an Ender 3 Pro build plate when at 45 degrees to the build plate. Will require glueing or...
myminifactory
The stepper motors are now covered and the cable loom is supported. Minimal support is required if printed with the cable entry hole on the bottom. Will fit on an Ender 3 Pro build plate when at 45 degrees to the build plate. Will require glueing or...
thingiverse
Customized version of http://www.thingiverse.com/thing:1672010 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1672010 Instructions Using the following options:...
thingiverse
Remixed this thing (https://www.thingiverse.com/thing:4646269) to be able just glue it to a shelf.
thingiverse
The printed part is threaded for 1/8" BSP.** This combines pneumatic M10 bowden tube fitting and cable loom holder for the railcore. No supports necessary, and the M10 fitting is designed to thread into the printed part. ...Print at 0.15mm layer...
prusaprinters
Custom fabric cable sleeves made from zippers and and Taslan. This is sorta lengthy, so I will just provide the build on a link to my blog, if that is cool: https://www.tardigradeoutdoors.com/blog/fabric-cable-sleeves-for-the-ender-3-3d-printer...
thingiverse
... sleeves made from zippers and and Taslan. ... This is sorta lengthy, so I will just provide the build on a link to my blog, if that is cool: https://www.tardigradeoutdoors.com/blog/fabric-cable-sleeves-for-the-ender-3-3d-printer Please post your makes!
thingiverse
Print as many as you need to perfectly route your cables along a steel surface! Apply silicone adhesive or similar into the main body. Insert magnet and press down. Apply more adhesive to the top of the magnet. Add magnet cover and press down. ...
thingiverse
Post-Printing None How I Designed This Based on my previous triangle wire loom just made it a cube version. Dropped the slots all the way down the side for wire drops. The bottom had a over hanging box added and the edges rounded with minkowski, this...
thingiverse
... flexible TPU filament. just cut a slice though each loop to open it up and insert it onto the frame and to insert the loom. There are cable tie recesses to secure both the frame and loom loops as well. ... Can be printed with or without supports
thingiverse
The TOP for SQUARE WIRE LOOM THING, http://www.thingiverse.com/thing:1675112 Please read description there. A WORK IN PROGRESS! ... FIXES needed: top thickness when scaled seems to thick.
thingiverse
I use this clip with the Bullseye duct horizontal wire management style (the cable management channel on the Bullseye / and Petsfang pulls the loom in a horizontal direction). The built in Ender 3 extruder clip doesn't hold the wire tight enough...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options: width...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options: width...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options: width...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1675112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1675112 Instructions Using the following options: width...
thingiverse
I wanted something to hold the cables and split loom vertical. My speeddrive remix uses similar holder. ... Printed on Ender 5 Plus.
thingiverse
I just wanted a version I could print that didn't use supports and accomplished the same task as Namemogan's "MK8 Extruder Wire Loom Cable Clip For Ender-3"
thingiverse
Parfait pour l'hypercube ou toute autre imprimante construite en profilé ! ... Un remix pour l'extrudé 3030 du support de cables pour les têtes d'impression.