cable protector floor 3d models
139301 3d models found related to cable protector floor.thingiverse
Multipart cable protector. ...Please read print settings carefully.
thingiverse
Cable / wire floor protector cover is designed to add multiple sections by snapping them together. This allows you to cover a large area on the floor to protect cables from being walked on. It will print under most settings. You can print it like...
thingiverse
Carpeted floor will stress the cable and protector more due to the substrate flex. You can minimize breakage of the bridge and cable by using a greater attack angle, looser fit, and a narrower, thicker bridge. For round cables, Attack angle = 30...
thingiverse
I needed some protection for a small cable running over the floor boards outside. The dimensions are 150 x 34 x 12 mm and the cable tunnel is 12 x 6 mm, rounded. ... It is probably more robust than necessary but it is for sure sturdy :-)
thingiverse
Provides a channel for cables to go across the floor without being a tipping hazard The dovetails will move when stepped on which does make some noise Each segment is about 6 inches long. Coners are rounded to help the dovetails slide together...
thingiverse
Customized version of https://www.thingiverse.com/thing:2651334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2651334
thingiverse
Customized version of https://www.thingiverse.com/thing:2651334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2651334
thingiverse
Customized version of https://www.thingiverse.com/thing:2651334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2651334
thingiverse
Customized version of https://www.thingiverse.com/thing:2651334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2651334
thingiverse
Customized version of https://www.thingiverse.com/thing:2651334 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2651334
thingiverse
New floor coming soon. Concerned that the six Dining Table castors (Narrow metal wheels) might damage it, so SCAD to the rescue. Each metal castor now has a boot clipping over it, with a 25mm self adhesive Felt Pad on its base. To fit the boot to...
thingiverse
Protector for headphone cable. ...Very useful when you have to pass it through a zipper.
thingiverse
This is a cable protector for Apple's type-c to lightning cable. The lightning side is a little bit shorter because of case interruption. Wish you like it. ...Give it a thumbs up if you so.
prusaprinters
1] print the cable protector according to the diameter of your cable (2.5 / 3 / 4.5)2] break the base :3] insert your cable printing tip :print at 200°C (for PLA)activate the fan
thingiverse
A spacer you can snap on a cable to keep it off the ground. ...Dimensions are parameters in the scad file. Default cable diameter is 12 mm (Chevrolet Volt charging cable).
thingiverse
I have made a protector you can print and glue over the worn out patch, you can print this again if needed. I tried some various filaments but you need a tough material so the teardrop plate doesn't break off. The best one I have had for many months...
cults3d
I have made a protector you can print and glue over the worn out patch, you can print this again if needed. I tried some various filaments but you need a tough material so the teardrop plate doesn't break off. The best one I have had for many...
cults3d
... when you glue them to fram or double side tape them, make sure you put all the protectors already under the frame, this way the protectors will be fit the way you want. The diameter of the round frame is 92 cm. ...The diameter of the tube is 40mm
grabcad
A rubber cord-concealed hump to protect cords on the floor from chairs, foot traffic, etc. ... Cord hum is 7' long in rubber (image shown for clarity).
prusaprinters
... that would chew up my floor. ...Since the base is curved nothing would stick so I made these.PETG.4 nozzle.2 resolution20% infillI just used adhesive felt on the bottom of the print to insulate from the floor and the curved legs sit in the saddle
thingiverse
... area with beveled edges and only exposes the top surface of the block. You could print in a color that matches the furniture, carpet or flooring. ...The .scad file is provided which allows you to generate a part to hold the size block you need.
thingiverse
I made this little thing to protect my wooden floors from chairs with stupid design. Print it with 100% infill and feel free to change measurements to whatever you need. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
USB Cable Protector/ Protector de cable USB Works to protect a broken cable
cults3d
X-Axis Cable Protector Version 2 . No one has told you that the artillery cable breaks? That's right, specifically this one on the x-axis, it has a lot of movement. With this part you can avoid this common problem. The design holds the cable...