cable shelf 3d models
122161 3d models found related to cable shelf.thingiverse
The original UP Plus cable shelf is easy to break so I made a new one. ...Enjoy!
thingiverse
This little clip slides onto the frame of the Printrbot Play to keep the cable up and stop it from getting caught on the bed as it moves back in the Y direction. ...Put a small piece of cloth in between to keep the powdercoated metal nice and add...
thingiverse
This desgin (v7) looks like a winner :) Update: 4/14/16: Completely parametized the design, so Andy's cable shelf is no longer necessary. You'll need Andy's cable shelf if you want to modify the .scad. Update: 4/12/16. Updated with V3. Much easier to...
thingiverse
... Play to keep the cable up and stop it from getting caught on the bed as it moves back in the Y direction. ...Remix of [@andyleer](http://www.thingiverse.com/andyleer/about)'s [ Printrbot Play Cable Shelf](http://www.thingiverse.com/thing:905768).
thingiverse
Cable shelf-organizer. Designed for 0.4 nozzle. ...On the photo it is a little bit shorter than in 3d model (you can adjust it buy yourself).
thingiverse
If you don't have a 3d printer but would like the 3d printed accessories, contact me at alexander[dot]maund[at]ntlworld[dot]com and I can sell you the 3d printed accessories at the following prices: PowerBank and USB cable shelf - £5 Spare Parts...
thingiverse
This is a cable organizer and a shelf. It has lots of room for your cables and power adapters. You could also put it next to your bed to hold your cell phone while charging and it will hold your phone's charging cable when not in use to keep it off...
prusaprinters
This is a cable organizer and a shelf. It has lots of room for your cables and power adapters. You could also put it next to your bed to hold your cell phone while charging and it will hold your phone's charging cable when not in use to keep it off...
thingiverse
My awful Arris CM820A cable modem is too tall to fit in a single U, so I came up with this 2u shelf to hold it. Also includes a hole for a keystone jack, so you can run ethernet to the front of the panel. The shelf attaches to the faceplate with M5...
thingiverse
I decided to make a support shelf to help relieve some of the leverage/ stress on these components. So far it is working well on my printer. It is adjustable up and down to get the perfect alignment. I recommend printing with a raft to help eliminate...
thingiverse
a simple cable passthrough with retainer pins
thingiverse
I print a few of these and line them up sequentially. ... Can hold a few power supplies and tidy up cables. ... 60mm height.
thingiverse
... due to the moment. This can be overcome with some double-sided tape between the holder and shelf, but this should not be an issue for most headphones. The design prints with no supports. ...I reccommend at least 3 perimeters and 20% infill.
thingiverse
USB, HDMI or just about any other cable hanger on a shelf. ... Turned-out to be strong enough and requires no fasteners to be held in-place.
thingiverse
This is a cable holder for 1-2 cables up to 6mm. It attaches to rivet-style shelving, common in the US (4cm spacing). No screws are needed, print it and slide it in. ... You will need some support to print this, I printed on its side and enabled the...
thingiverse
This is a cable holder. It attaches to rivet-style shelving, common in the US (4cm spacing). No screws are needed, print it and slide it in. It holds 4 cables. ... You will need some support to print this, I printed on its side and enabled the "snug"...
thingiverse
Simple LACK shelf cable management that uses a 27mm wide velcro strap to hold cables.
thingiverse
Simple cable clip to tidy cables on this Ikea shelf unit. ...Recommend using black filament so it matches the colour of the shelf frame.
thingiverse
I used it for hanging an HDMI cable across the shelf. ...Print Settings Printer: DaVinci 1.0 Rafts: Doesn't Matter ...
thingiverse
Cable holder for IKEA IVAR shelves, for example for your printer (like me). ...Enjoy!
thingiverse
A clip for the Ivar shelves to hold a cable Instructions The Sketchup files are included, you may want to make the hole larger for larger cables. ...Printed on a Makerbot Thing-O-Matic.
prusaprinters
Cable holder for IKEA IVAR shelves, for example for your printer (like me). ...Enjoy!</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p><p class="detail-setting printer"><strong>Printer: </strong> <div><p>Ender...
thingiverse
I designed this holder to clip onto some shelving I have to organize my USB cables. There are twelve slots and the back clip is designed to fit a 3/4" shelf. I haven't sanded the clip in the photos, but it fits snugly on my shelf and works great. ... ...
cults3d
Fully customizable cable holder to clamp on a shelf.
thingiverse
Fully customizable cable holder to clamp on a shelf.
thingiverse
Cable holder to fit the end of a IKEA shelf http://www.ikea.com/dk/da/catalog/products/40126069/ Made to fit small wires for iPad chargers. 2 screw holes to fasten the cable holder to the shelf. ... Print without support 0.2 layer
thingiverse
Put loops under the shelf to strap cables to, and some mounting holes. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/32kReF5cKbw Instructions no rafts or...