cable tidy box 3d models
281283 3d models found related to cable tidy box.thingiverse
Cable tidy for my BMG extruder mount: https://www.thingiverse.com/thing:3541189 This comes in two parts for easy cable routing. ...Needs M2x20mm screws and nuts to complete.
thingiverse
This is a mountable desk cable tidy with 5 seperate slots. Supporting cables up to 5mm^2 θ, possibly 6mm at a push. ... Screw size: M3.5 x 15mm - Countersunk
thingiverse
... D1 (Red and Gold), which covers cable management. However when I went to order these I thought they were expensive for that they are so, I came up with this. Once you have stuck the 'tidy' to the tool, then use cable ties to fasten the cable to it.
thingiverse
Originally this is for Firefighting comms PTT cable tidy attached to the webbing strip of firefighting tunic/coat. ...The firefighting helmet comms is connected to the PTT hand piece.
thingiverse
Pen holder and cable tidy for Wacom Intuos3 tables. Can be positioned anywhere along the back edge. ...They are designed to slightly grip the tablet but I would also recommend using masking tape underneath to keep them in position.
thingiverse
Designed this little cable tidy bracket for my MicroSwiss direct drive/All Metal Hot end. ... After fitting the kit I found my cables needed somewhere to be attached so I used the fixing points for 'BLtouch' I think to mount this bracket and secure the...
thingiverse
My earlier design for a Kossel cable tidy was designed to be screwed to an extrusion, then the cable slipped under the loops. However, it was sometimes difficult to slip the cable through the gap at the side of the loop, and it didn't grip the cable....
thingiverse
This is a simple cable tidy that mounts onto the vesa mounting holes on the back of the monitor. ... This is a cheap and easy way to hide cables on the desk which are just an eye sure I hope this helps someone, I'd be more than happy to model this to...
prusaprinters
I took the idea and some nodes from SkyTake's cable clips for my fasteners. Once assembly is complete, check that your 3018 has full movement in all axis. My CNC 3018 Pro Things Circuit board housing Thing:3886992 Cable Tidy Set Thing:3888299 Limit...
thingiverse
CNC 3018 Pro Cable Tidy Set =========== Tidy up the loose cables of your CNC 3018 Pro. I provide a STL file of all clips which will fit on my print bed together with the individual component files in case you need to rearrange them or reprint some of...
thingiverse
An alternative is to use relative 'turtle graphics' commands to walk the boundary and then convert these steps to a polygon and hence to a 3D object The examples are designs for a cable tidy. The first is a simple one polygon design. The second...
thingiverse
The design is optimised for wire of 8mm cross section, but the slot in the cable outlet is intended to take a cable tie and can grip down to 6mm (or smaller with a modification, or a bit of filing) It is intended to attach with epoxy glue. Mainly...
thingiverse
Based on this (https://www.thingiverse.com/thing:4656494). ... I just extended and added bits and pieces so it would work with the SV03. No additional hardware needed; it snaps in to the extrusion. Keep it tidy!
thingiverse
... cable holder that also doubles as a stand. ...The storage can be utilised to shorten the cable when used as a phone stand. This has been designed to be used with a USB-C cable or a Anko iPhone cable. ... There is enough storage to hold a 3m cable.
thingiverse
Simple suppoort to keep the hot end cables secure on my CR10s Pro by slipping over the wheel cover on the hot end carriage. ...2 cable ties keep the cable secure in place.
thingiverse
I found that my hotend cables and bowden tube would catch and get wrapped around the X motor, so I have redesigned the standard motor cap with a notch to cable tie the cables and tube too.
cults3d
this is for those sets of head phones where the cable is too long and awkward to use. ...this allows you to wrap the cable round and feed it though to keep it at the length you want.
thingiverse
this is for those sets of head phones where the cable is too long and awkward to use. ...this allows you to wrap the cable round and feed it though to keep it at the length you want.
thingiverse
Fed up with USB cables vanishing down the back of your desk when you unplug ? ... Print one of these and shove it on the desk.
thingiverse
Basic tab to hold cap lamp cable to the side of a mine helmet. ...Slots into ear defender attachment holes, but can't be worn with them.
thingiverse
This is just a basic cable clip to go on the back of most soft back chairs to stop the htc vive cable from sliding down the sides of the seat while in seated VR. ... works really well, and does not need glue or screws to hold itself in place, just...
thingiverse
The Heath Robinson elastic band and cable tie at the top just keep the cable more or less stress free. Makes sure it is more or less vertical. Cable tie slides on the rail a bit, rubber band means no solid fixing. I just wanted the cable to move...
prusaprinters
Basic tab to hold cap lamp cable to the side of a mine helmet. ...Slots into ear defender attachment holes, but can't be worn with them.</p> Category: Engineering
prusaprinters
to suit ikea fredde desk that has the 20mm thick lower backboard (new fredde style with oval tubing).my own quick design for getting the cables neatly organised that were drooped behind the ikea fredde desk, I was using adhesive cable management pads...
thingiverse
my own quick design for getting the cables neatly organised that were drooped behind the ikea fredde desk, I was using adhesive cable management pads to the rear but they had failed and whole desk would need to come away to sort, so easier to make...
thingiverse
This object is a clip that attaches to an IKEA LINNMON table, for cable organization. I use an IKEA LINNMON as a desk, and found this would be very useful. Just push onto the tabletop, and you have a handy hoop for running cables through. Print...
thingiverse
This is the desk attachment portion for an Allcam Cable Slinky/Spine (https://www.amazon.co.uk/dp/B085CDFB12). When I bought this item, I managed to slice my finger open on the razor sharp desk fitting attachment, so quickly chucked this together and...
thingiverse
Screwed clip for under your desk / or wall mounted Cables can be slipped in and out as required without removing the clip's Needs screw's, the hole is 5mm diameter. ... Instructions Printed no support, 3...
thingiverse
This is an attachment for a Ninja IQ Smoothie maker, to allow you to stow the power cable neatly. The attachment is designed to lock around the motor mount snugly, but still be removable. It has holes in it to allow air to circulate freely. ... The...
thingiverse
Note that this is designed to hide all of the cable/plug within, and also to sit the charger to make it flush and to get rid of all wires. It prints in two parts, one part is for the facia around the socket, this is a standard UK shaver socket,...