cable tie wall mount 3d models
595675 3d models found related to cable tie wall mount.cults3d
......The tubes are 40mm white drain pipes that are cut to the desired length, the bottom plugs are glued with CA glue. The holder are fastened to the wall with two invisible screws and the tubes are fastened with 3x6mm tapping screw with countersunk head.
thingiverse
......The tubes are 40mm white drain pipes that are cut to the desired length, the bottom plugs are glued with CA glue. The holder are fastened to the wall with two invisible screws and the tubes are fastened with 3x6mm tapping screw with countersunk head.
thingiverse
Cable tie wall mount It can be used by sticking it to wall or other surfaces with double sided tape Dimensions of the zip tie hole: 5 mm x 2.4 mm Total dimensions: 20 x 20 mm Inside dimension: radius: 3.5 mm
thingiverse
Mount for cable ties. ...Glue it onto something an pull the cable ties through it.
thingiverse
mount for fixing cable (ties) to furniture or walls with a single 2mm picture hanger nail. No special print settings needed - should print in only a few minutes per piece. ...Scale if bigger cable ties or nails / screws are used.
grabcad
Just a simple cable tie mount designed for standard width cables and smaller. ...Use mounting tape.
thingiverse
Cable wall mount for securing cables and such via velcroe cable tie or zip tie. The larger one has screw hole spots and is 50 x 50 mm. ... The smaller one is 25 x 25 mm and has no screw holes.
cults3d
Cable tie mount dimensions are 25x25x5mm. Accepts cable ties of 5.5mm wide and 2.5mm thick. ...Apply double-sided adhesive tape to the base.
thingiverse
Cable tie mount dimensions are 25x25x5mm. Accepts cable ties of 5.5mm wide and 2.5mm thick. ... Apply double-sided adhesive tape to the base.
thingiverse
You can be screw mount this Cable mount at anywhere. ... Dimensions:- Outside : 20mm x 20mm Hole for Screw : 3mm Hole for Cable Tie : 5mm(W) x 2mm(H)
thingiverse
Universal mount for gopro. ...You can mount int to example bicycle helmet using cable tie or Velcro. ... "wkret_myn_10mm.stl" - is for mounting screw
thingiverse
Cable tie mount dimensions are 20x20 (base) Accepts cable ties of 7 mm wide and 2.5 mm thick Apply glue or double-sided adhesive tape to the base
thingiverse
Cable tie mount: 20mm x 20mm x 6.6mm Cable tie openings are 5mm x 2.2mm. Top hole is 5mm x 5mm. Printed in PLA, .2mm layer height, 2 shells. Use adhesive tape on the back. ...
thingiverse
A couple of different cable tie mounts. One with the cable tie attached in the middle, and one that allows a bit more variation. ... Designed to fit the Pattex No More Nails double sided tape (19mm wide).
thingiverse
Small plastic mount designed to hold a cable tie in either direction. ...Requires some double-sided tape or some hot glue to mount.
prusaprinters
This is a small cable tie mount for cable management.Printed in Polymaker Polylite PLA pro in about 4 minutes .The cables or wires are routed next to the mount and a cable tie goes through the hole wrapping around the mount and wire/cable. ...The flat...
thingiverse
This little mount provides a good space for about 1 to 3 cables to be organized. Use a zip tie to keep the cable from coming out of this anchor. ... I use command strips to connect this to a surface.
thingiverse
I just needed some cable tie mounts and after a little drawing this was the result. I had some 12mm double adhesive tape, so they are 12x12mm Instructions Print and mount with double adhesive tape. ...The hole for the cable tie is 3x1,5mm.
thingiverse
simple and quick to print cable tie mount for use with double sided tape as always comments and feedback if appreciated ONJ files available upon reasonable request cable ties https://tinyurl.com/34hzf3t2 double sided tape https://tinyurl.com/yp75ymfh...
cults3d
simple and quick to print cable tie mount for use with double sided tape as always comments and feedback if appreciated ONJ files available upon reasonable request cable ties https://tinyurl.com/34hzf3t2 double sided tape https://tinyurl.com/yp75ymfh...
thingiverse
Sticky cable zip tie mounts for management of cables. A double sided adhesive tape needs to be attached on the back. ... Additional material: - Double sided tape, for example, 3M VHB Tape 4910F 19 mm x 3 m x 1.1 mm - Zip Ties, up to 4.8 mm wide - M4...