cable tv sucks 3d models
117635 3d models found related to cable tv sucks.thingiverse
... ...The idea is that the cables go in the center of the TV and this cover the cables, so they don't show. ...This applies only on a TV that is standing on a table-like stand, especially when the stand of the TV are on the sides, instead of the center.
prusaprinters
This is a cable cover to hide the cables running from the TV to the tv cupboard. Simple design, print the 2 parts, the smaller part screws into the pin in the back of the bigger part. ...Now you can put it over the cables with the smaller part being...
thingiverse
This is a cable cover to hide the cables running from the TV to the tv cupboard. Simple design, print the 2 parts, the smaller part screws into the pin in the back of the bigger part. ...Now you can put it over the cables with the smaller part being...
thingiverse
I've created a wall cable channel to hide the TV cables of my wall-mounted TV. You have to print 2 or three clips for each 30cm Lid. The tiny clamps are designed to keep the cables in the channel in place. You could use them or not ;-) you can...
thingiverse
It´s a HDMI Cable Holder for the backside of your tv. If you like it and like to show some love, than please share it or add it to your list. Enjoy ! ...:) JoeyHills.de 3Dsection.de
thingiverse
Clips into the original grooves on the back of the TV (which do a rubbish job of holding the cables in, hence this thing!) let me know in the comments and makes which other TVs this works on, and i will update the list! ... Confirmed fit: ...
thingiverse
I mounted a TV on the wall and wanted a simple cable cover.. The idea is the "Top Cable Cover" would be flush to the wall. The bottom as two screw holes, for mounting to the wall then the top clicks in.. When I installed its I found no need to...
thingiverse
This is a cable guide to assist in feeding the Samsung Frame TV one connect cable through internal walls. The first part fits over the front of the small connector, and has a cut out to allow a cable to be connected for pulling. The pull cable can...
thingiverse
This is a super simple design to manage all those cables that are hanging from below your tv. The object is 100mm long. Print as many as you need and just line them up together. You'll need either command strips (what I'm using in the picture)...
cults3d
This is a super simple design to manage all those cables that are hanging from below your tv. The object is 100mm long. Print as many as you need and just line them up together. You'll need either command strips (what I'm using in the picture) or...
grabcad
... devices. Made from ABS plastic, it's 3D printable, making it accessible and user-friendly. This design, created by Pleasant Grove High School student under Instructor Colin Denny, simplifies cable organisation for a professional appearance.
thingiverse
Customizable TV cable duct consisting of an inlet and outlet as well as duct parts that can be sticked together to get the length needed. Diameter of the inlet and outlet is 60 mm. The duct parts have an effective height of 17.8 cm, inside dimensions...
prusaprinters
The cable concealer consists of two parts: The base which holds the cables and is glued to the wall.The cover which is attached to the base with tabs.The concealer accepts 3x 6mm diameter cables (typical HDMI and Ethernet cables) and 2x 3mm by...
thingiverse
Small cable clip for the Samsung UE49NU7170SXXN smart TV.
thingiverse
... the Besta series by Ikea. ... I took advantage of the attachment of the cable pass slot cover to fix the cable cover channel. When using the lid hook, the channel does not require supports: it stands upright by itself. ... Visible height 7 cm.
thingiverse
**RG6 Coax Cap** This caps off the pokey male end of a cable tv coaxial cable. Didn't see anything quite like it available so I designed my own. Print with hex side down. ...3/8-32 UNEF 2A threads came out perfectly on my prints and worked great.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=2054634 Instructions Using the following options: text_thickness = 2 text = TV Room text_font = Acme text_size = 10 cable_diameter = 6.5 main_body_length = 85 rotate_text = parallel...
thingiverse
Overview: you should have no tension or slack on the TV cable at idle and therefore should be 5psi or less at the correct test port. With this 10mm long tool temporarily on the cable pulling it out the pressure should be about 33psi. See a...
thingiverse
The entrance features cabling, making it convenient for wire installation and management.
thingiverse
Customized version of https://www.thingiverse.com/thing:3681367 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3681367
thingiverse
Customized version of https://www.thingiverse.com/thing:3681367 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3681367
thingiverse
Adjustable ear saver with the phrase "COVID SUCKS!" slightly raised.
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=40704 Instructions Using the following options: message = alexis sucks!! ...ring_size = 17.32 font_size = 15 font_spacing = -26 Font = write/Letters.dxf ring_width = 6 ring_thickness = 1.6
thingiverse
You can put these cables for cable management on your pc, wall, tv, or any flat surface to hold cables. ... If the cable you are using is too big or too small just adjust it from your slicer before printing.
thingiverse
This should fit on a F connector for a coaxial cable for a TV antenna or cable TV in the US. It is suppose to help make tightening it down easier. Please print and let me know! :) Instructions I saw something similar that came with a coaxial cable...
thingiverse
Basic TV remote holder with USB cable route notch for a nightstand. Front shorter section is designed to fit JLab wireless earbuds in the case. 2nd section is perfect for Fire TV remote and back 2 should fit universal remotes. ... *Updated wall...