calibration cube ender 3 v2 3d models

Printed and tested on an Ender 3 using Simplify3D without any problems at all - it works great! Note: This is just one part of a set; you'll still need the other two pieces from the link above to complete the design. Note 2: I used 0.4mm for...

I needed a large drawer for the left side of my Ender 3 Pro. I printed these dual drawers for the front of my printer: https://www.thingiverse.com/thing:3416444 Then I upgraded to the Rear Electronics Case from Teaching Tech: ...

... CURA alignment. 15.06.2021 new style for Large cover Enjoy! Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 25% Filament: Polymaker Polyflex TPU Black Category: 3D Printer Accessories

Needed a big drawer for the left side of my Ender 3 Pro I printed these dual drawers for the front of my printer: https://www.thingiverse.com/thing:3416444 Then upgraded to the Rear Electronics Case from Teaching Tech:...

Y axis Linear Rail for ender 3 Series. Its not perfect. ...maybe you can contact me for i revised

Y axis Linear Rail for ender 3 Series. Its not perfect. ...maybe you can contact me for i revised

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

This is front power switch relocation box developed for my V2 I would recommend supports for the box Uses M2x8mm screws for the cover

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

Spool holder for V2, you will need to source: - M3 x 20mm. - M3 x 15mm. - M3 Brass insert (2 needed). ... - 22mm OD/ 8mm ID bearing (6 needed).

Support for the Pi Camera v2 is on the Y-axis. With good ventilation, the box prints without support. ... It requires an M4 screw and nut.

This is a remix of Ender3 v2 mainboard 92mmfan cover NO support by Csoki96. ...I wanted the same flat cover design but for a 80x80mm fan.

While doing my probe calibration the results were actually -47 and -7 . ... This satsana is using mixed parts from: https://www.thingiverse.com/thing:4647053 https://www.thingiverse.com/thing:4637453 https://www.thingiverse.com/thing:4369859 ...

This is a remix of a good design, but I have added a diode (3 mm, red, 2V, 20 mA) with 510 ohm resistor powered by the same converter as the fan (12V) and the LED is in the eye of Ender dragon which I have added to the front face of this cover. I...

It's a snug fit but cannot fall out the other side because of the back stopper. I printed it at 10% infill at .2 resolution with 2mm thick walls I would recommend adding a support blocker on one side of the top to help you remove supports otherwise...

Chopped off the piece to clip it into an ender frame, making it flat instead. Added two holes for screws. ...Can be used with an LACK enclosure etc.

Made to fit Ender 3V2 but should fit any 20x20 extrusion. ... my need slight filing or sanding on posts as it is a pretty tight fit.

Soulsmith from the Will Wright Cradle Series. ...I Thought it would make a nifty badge for the ender 3v2, Remixed using Tinkercad.

Made to fit Ender 3V2 but should fit any 20x20 extrusion. ... my need slight filing or sanding on posts as it is a pretty tight fit.

This is a remix from https://www.thingiverse.com/thing:4756995 I just added the Ender Logo. ... Print vertical without supports

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy

This is a remix from https://www.thingiverse.com/thing:4756995 I just added the Ender Logo. ... Print vertical without supports

measured it best I could and flipped it ~ and stretched it Printed and functional v3 because v1 wasn't long enough and v2 wasn't wide enough to fit the screen v3 is a little too wide but it is functional This is V3 I lost v1 and v2 wasn't worth the...

Tight fit in V-slot regardless of the printer calibration. Fast print. Side Cutter Holder https://www.thingiverse.com/thing:4068810 5-minute USB Holder https://www.thingiverse.com/thing:4647129 Spool Holder Slider...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Infill: 15% Notes: Printed with most of the flat side on the bed, a little support is needed to create the v-slot rails.The object should be orientated correct already...

(this is why there is a space near the SD card slot) Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: your choice Filament: Sunlu PETG/PLA/ABS any Notes: Fan mount is for a...

You do have to be careful not to tighten these screws because you will put stress on your leadscrew and cause printing issues. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.12 Infill: 10% Filament:...

I am no expert on electronics, so I don't want to add a how to connect the cable to the 24v ender 3 power supply and ruin your printer section. I just connect the + - cables to the output and it magically works.. I added this...

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...