calibration cube ender 3 v2 3d models

... Screws used for attaching the bottom and top case are M2.5x6. Perfect for OctoPrint (I have the GPIO pins hooked into a relay board in a separate case to control PSU and LED light). Slides into the channel on the Ender series 3D printer structure.

This is a custom Ender 3V2 mainboard cover designed for the use with a 92x14mm fan (e.g. Noctua NF-A9x14 PWM) in conjunction with a 22x7mm step down converter (e.g. MP1584EN). There are clearance holes for using the fan either in a push or a pull...

This is a moving camera mount for ender 3v2 neo. I created this to add a wifi camera to my setup to monitor prints. Print this in a lower layer height to make sure the quality it there for it to slot together. The end of the pin did break off for...

This is a custom Ender 3V2 mainboard cover designed for the use with a 92x14mm fan (e.g. Noctua NF-A9x14 PWM) in conjunction with a 22x7mm step down converter (e.g. MP1584EN).</p><p>There are clearance holes for using the fan either in a push or a...

Simple full power supply cover replacement to install silent fan on the Meanwell PSU of the Creality Ender 3v2. This design is for 80x80x10 fan, in my case i used this one : ...

Posts to mount 120mm fan under Ender 3v2/Pro motherboard note: this is really still work in progress note2: For this to work, the drawer has to be removed Hardware required: 120mm pc fan, I'm using an old be quiet! PURE WINGS 2, but any other brand...

------------------------------------------------------------------------------------------------------------------------ V2 UPDATE...

* Benjiis Bed Wire Strain Relief is not usable for Ender3 V2, because V2 has PSU there. I redrawed new one, using <a href="https://www.thingiverse.com/FourDogs">FourDogs</a> "<a href="https://www.thingiverse.com/thing:2958812">bed wire strain...

- Camera Arm V0 - Original Arm with Radius - Camera Arm v1 - Original Arm with Bevel - Camera Arm v2 - Shorter Arm (z-axis) Added Additional Pivot pins for clearance issues : - Pivot Pin v1 - 0.00mm clearance - Pivot Pin v2 - 0.10mm clearance -...

Print with supports touching build plate0.2 layer height3 walls

There are three files: * both objects combined in the orientation I suggest printing them * the tower alone * the base alone The screw holes should print without supports on a well-calibrated printer capable of short bridging. ... The slot in the top...

I accidently printed this thinking it would fit my V2 (I know I didn't read his description) So I made this fit. Just elongated between the two semi circles. Fit snug for me. I may remake this and make it a mm or two longer if there are too many who...

This is a hotend housing for the zesty nimble v2 which features a built in and adjustable mounting platform for the bltouch and 40 mm blower as well. Print with the large fan opening down and use supports for two mounting tabs. There is only one...

Update v2: The previous design allowed for slight extruder flex when filament feed wasn't perfect. This new version now includes a front plate connected to the base via 2x countersunk M6x8 screws (IKEA scraps repurposed). It still works with the...

However, I've included the original V2 version as a precautionary measure. UPDATED: 8-4-2018 The initial (V1) version featured threads to screw on the filament holder. Unfortunately, there was an issue with the threads being excessively loose. To...

......For the Ender boards or SKR. Not sure what else will fit. Moved the left side fan hole over and mirrored it over to the right so the pi and main board both are getting a good solid flow of air across the hot bits. Also added the honeycomb cutouts.

This screen holder mounts on the left front side of the bracket using the 3 already available screws.

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot

There are 3 covers & 3 handle variants. Post processing: 1. Lightly sand the underside of the handle. 2. Pre-align where you want the handle to be on the cover. 3. A few drops of super glue on underside of handle. 4. ...Stick the handle on the...

dust cover for x and y tenshion rails made from original to fit other 3 holes file has all 4 to print. ...about 30 min print time

Remix to fit 3 LM2596 buck converters and 8025 fan to PCB Needs these legs to work https://www.thingiverse.com/thing:4603075

you can replace this with the cap of the original spool and have a double spool as well, its width is 3 cm so any filament can fit

dust cover for x and y tenshion rails made from original to fit other 3 holes file has all 4 to print. ...about 30 min print time

... ... https://www.thingiverse.com/thing:4904382 This bracket includes a 3D printable pin instead of having to use a screw and nut however the hole on the spool holder must either be sized to 3/16" or can be drilled out using a 3/16" drill bit. ...

I wanted my spool holder to be able to hold 3 500g spools for easy color switching. ...This extension just slides in the original spool holder with a tight fit and extends it by 35mm.

Printing this https://www.thingiverse.com/thing:4627925/ and instead of cutting into the psu shroud, I instead took off the external cover and designed this to cover up the electronics. ...fits perfectly using 2/3 of the stock screws.

Remix of https://www.thingiverse.com/thing:4604339Wanted to make it fit a Pi 3 A, so moved screw holes and changed usb slots.To print, follow his guide.

3 parts cooling fans you will need extra screws for the extra fans, and they need to be spliced into the existing fans wiring. blower ducts are glued on, sounds dodgy but works for me. ...

This is simple holder for memomry cards. ...It has one slot for SD Card, 2 USB slots and 3 microSD slots. ...It is mounted in the V-slots on the base.

I used a Nordlux Latona 4W white, a cheap led from my local hardware store. ... Size: 3,4 x 31,2 cm Where i bought it: https://www.bauhaus.dk/nordlux-lysarmatur-latona-4w-hvid