camera ground glass 3d models
195625 3d models found related to camera ground glass.thingiverse
--> You've seen old-time "view cameras" in movies - this is exactly how the "view" is composed before the film is exposed after swapping the ground glass for a loaded film holder. This will fit any camera that uses a standard 4X5 film holder. The...
thingiverse
Pressure plate which holds the glass screen in place and is also used to pull the screenframe and filmholder towards the camera body. I decided to hide the elastic bands inside the structure for a sleeker design and to make them less prone to...
prusaprinters
You're not stuck with needing to adapt your camera to use Graflok back or looking for a more expensive one with it already attached.M3 Screws hold the ground glass and viewfinder mask on. I use heat-set inserts for them to screw into, but...
thingiverse
The Attachment clamps are separate parts screwed to the upper frame, so you can easily print frames specific to your camera models ground glass holder. I've included clamps which should be compatible with all 4x5 Chamonix screens, with two options...
thingiverse
... powdery white coating when in a closed space. Make sure to remove or cover your lens inside the camera body and make sure to keep the back open and well ventilated for at least an hour before replacing the ground glass and uncovering the lens. ...
thingiverse
This is a 4X5 ground glass holder for large format cameras. It has the same dimension as a regular film holder and is used the same way. The strip is glued in the slot and keeps it from sliding out acidentily. It's made for 4mm thick frosted glass.
cults3d
DIY 4x5 glass ground. Using a very cheap 0.70€ 10x15cm frame glass (1,6mm thickness). That glass has to be frosted (take a look at youtube to do that). ...Needed 7 machine screws M3x9 or M2x9 Can be printed with PLA and ABS (if warping is acceptable).
thingiverse
DIY 4x5 glass ground. Using a very cheap 0.70€ 10x15cm frame glass (1,6mm thickness). That glass has to be frosted (take a look at youtube to do that). Needed 7 machine screws M3x9 or M2x9 Can be printed with PLA and ABS (if warping is acceptable).
thingiverse
A remix from the OG 4x5 ground glass holder. The original one was 2mm short for me and the top channel wouldn't line up perfectly for me. the top channel didn't quite fit after I printed it so I shaved off some plastic to allow locking. In this...
thingiverse
a version of the spacer that goes into the graflok system but this holds the glass plate directly so that there is no need to slide the spacer in and out all the time. Just slap onto the back for focus, then replace, holds together as one whole...
thingiverse
Create a insert for a 4x5 ground glass for the WillTravel 4x5 camera. Glass I purchased. ... 127x101x2.0 Grid A https://www.ebay.com/itm/224651877758
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/b7Tn4kLW5f0 Protective cover for Ground Glass -Fit -rotating back CAMBO 4x5 Large format camera Printed -Stlll need some tweaks !
prusaprinters
This is a simple printed instax wide cartridge designed around a Pentax 67 focusing screen from a broken viewfinder I had lying around.I use it to help with finding infinity and rangefinder calibration for my 110 conversions.I've included the STEP...
thingiverse
### There are three STLs to print: * (1x) - **Ground Glass Holder.** This holds the ground glass, and interfaces with the Goodman Zone camera body using 4x2mm cylindrical neodymium magnets. * (1x) - **Ground Glass Shade.** This optionally attaches...
thingiverse
The troughs along the sides house the elastic that holds the ground glass to the camera and the lip on the sides help keep it centered. I made two versions - one with shallower/longer troughs for the elastic and one with deeper ones (that's also a...
prusaprinters
I managed to crack one of the lower tabs that help hold the ground glass to the camera. This happened when I was trying to have the magnets break free so I could rotate the ground glass orientation. Upon inspection, I noticed that the tabs, at least...
thingiverse
The ground-glass side fits a 50mm ground glass available from Edmund Optics. In the video I am using a 220 grit glass. Instructions Printing is very easy, just print with the lens-side down. The...
prusaprinters
They use a Sneaky Pete Mega Globe from Vape Wellness to bubble filter their medical cannabis vapour.DesignThe glass pass-through adapter pictured has standard female 10mm and 14mm ground glass fittings. These stoppers will fit snuggly, leaving the...
thingiverse
A mount that you can place on top of a glass window or flat panel to hold a small video camera
thingiverse
This piece slides snugly over your Glass' body and masks the camera. You obviously won't be able to take pictures, but all the more useful functionality will work just fine. This improved version adds a small hole that allows the light sensor to...
thingiverse
Decided to model a glass on glass (joint) clip for my Grav Labs 14mm reclaimer adapter so I would have a spare or two. Instructions raft and support recommended. ... printed @ 0.20mm, 2 perimeter...
pinshape
SummaryDecided to model a glass on glass (joint) clip for my Grav Labs 14mm reclaimer adapter so I would have a spare or two.Instructionsraft and support recommended. ...printed @ 0.20mm, 2 perimeter shells and 40% infill
thingiverse
This is a stand made for the Glass Symphony, but it should work with any 24mm male ground glass joint. This was successfully printed in porcelain via shapeways and works/fits very well. I also included the cone I use to make joints in models. ...I...
thingiverse
Inspired by Luis' remixed version of the original, I trimmed it as well. ... Perfectly slides onto the Glass and keeps the prism clear.
pinshape
Inspired by Luis' remixed version of the original, I trimmed it as well. ...Perfectly slides onto the Glass and keeps the prism clear.
thingiverse
A quick print to join 14MM male to 18mm male ground glass connections. ...Print with the 14MM side down for best results.
thingiverse
One of the missing parts was it's spring back film holder including the ground glass holder. Because I had another 4x5 Speed Graphic, I had a frame to use as an example to design a copy. Some of the details were a bit intricate, so it was a challenge...