camera mount thread size 3d models
905758 3d models found related to camera mount thread size.thingiverse
A two piece mount to hold a QHY5III camera with a threaded hole for a standard camera thread screw (1/4" 20tpi). ... Space for two zip ties to secure the halves of the mount, a piece of tape on the inside of the mount can sure up any looseness in fit.
thingiverse
This mount was designed for the Logitech C270 Webcam in order to thread onto an articulating arm, in this case to view a 3D print remotely. After the file has printed, the large hole in the bottom will need a 1/4"-20 heat-set insert that is 0.5"...
thingiverse
I have designed this mount for micro camera style such as Foxeer Arrow Micro or Foxeer Predator. ... This mount allows you to have low profile Alien quad, i use 25mm standoffs and quad is completely diferent compared to standar size standoffs
thingiverse
... to hold a Sony XCD-SXxx0 series camera, modeled to fit an SX910UV but should fit anything with the same housing. ... This leaves four holes on the underside for M3 screws into the camera body and converts it to a single 1/4" 20TPI camera mount thread.
thingiverse
I designed it to fit a full-size mount (28mm) and also push the camera far out enough that it clears the standoffs. Standard M3 bolts are used to secure it to mounting plates. To install it, I put some 3M sticky tape on the back of the camera and...
thingiverse
... AQ250 and my Sony 600TVL Super HAD II from SecurityCamera2000.com. ... It attaches to the frame with 4 small screws and connects to the camera by protruding through the holes, then you can melt the ends down with a soldering iron to fix it in place.
thingiverse
**Buy The Frame Here: https://store.bicks.us/** **Print Settings:** Make sure to print out of TPU, and with the side mount flush against the bed. Support needed, unless your printer has godlike bridging on TPU. I'd recommend 2-4 walls, and infill is...
thingiverse
Cap mount to PET bottle for action cams like GoPro and other...
thingiverse
Print Settings: Make sure to print out of TPU, and with the side mount flush against the bed. Support needed, unless your printer has godlike bridging on TPU. I'd recommend 2-4 walls, and infill is best at 10% or higher on a 0.4mm nozzle with 0.2mm...
thingiverse
**Buy The Frame Here: https://store.bicks.us/** **Print Settings:** Make sure to print out of TPU, and with the side mount flush against the bed. Support needed, unless your printer has godlike bridging on TPU. I'd recommend 2-4 walls, and infill is...
thingiverse
Adapter for fitting 10mm (3/8 -16 UNC) female TO 6mm (1/4 - 20 UNC) male. ... Maybe not best for continuous use, but does its thing (of course depending print material and settings) I recommend 100% infill for strength.
thingiverse
... dual gigabit industrial camera, modeled around an LXG-20NIR and tested. ... Mounts to the two M3 holes in the bottom and the bottom two on the front to secure it and has a threaded 1/4" 20 tpi hole in the bottom for a standard camera threaded mount.
thingiverse
Exposed camera mount for the Raspberry Pi camera so you can enjoy the electronics. ...The thread is a 3/8-16 UNC for putting on a tripod or similar.
thingiverse
... the Original Design by fatmanl. ...New Camera-Arm to mount the Camera thru a tripod thread. tripod screw (1/4-20 screw) as separate model. 08.01.2023: Added an lower X-Axis-Mount for a better View on the Nozzle. ...See Photos with black X-Axis-Mount.
thingiverse
... a JAI CM-140 GE series camera, modeled to fit a CM-140 GE-UV but should fit anything with the same housing. ...This leaves four holes on the underside for M3 screws into the camera body and converts it to a single 1/4" 20TPI camera mount thread. ...
thingiverse
... ...So I made a 5/8" microphone stand thread in tinkercad and plopped it on the top of the this tripod mount adapter. Resulting in this monster, but it works both my camera and microphone are up off my desk thanks for my monitors included tripod mount.
thingiverse
... Also, need to tap the hole with 1/4th thread tap in case you need to mount on tripod. The tolerences are well matched that even if you don't put screws, the plastic goes as snug fit and can be easily removed too as seen in the jpeg preview here.
thingiverse
ULANZI Quick Release Magnetic Mount is a great design for mounting action cameras or digital cameras. But they didn't design the 1/4 inch male mount for cameras. So I made this model. Even it is not as static as a tripod release mount, but it is...
thingiverse
These mounts are everywhere (there are over 3000 camera mounts with 4+ stars on Amazon) including on Tripods, Brackets, Monopods, Booms, etc. Being able to use these tools to position AT Switches is a huge advantage and these "things" will help...
prusaprinters
This is the first of several mounts that are designed to convert an Assistive Technology (AT) Switch to fit on standard camera mounts. Camera mounts are 1/4"-20 female sockets. That is, they take a standard 1/4" bolt with 20 threads per inch. These...
thingiverse
... pitch to print threads even at 125um), I opted for a standard metal bolt so it was easier to torque down and back out if needed. Update 1.1: Added a base for the camera core that will screw into a standard 1/4" 20 TPI threaded camera mount as well.
thingiverse
Micro camera mount compatible with (some?) 130-sized quads Width (between centres of the holes): 13.5mm Height: 25mm 0, 15 and 30 degrees angle versions available
thingiverse
Simple adapter plates to mount a Walksnail HD V2 (and other similar) camera where a standard size (28mm) camera would go. I provide two lenghts - the longer one should put the camera lense pretty close to where a standard camera would land. ...The...
thingiverse
Basic fullsize and mini camera mount for the Hyperlite EVO, Hyperlite FLOSS and the Hyperlite FLOSS 2...as well as any 30.5x30.5 standoff mount.
thingiverse
Handle for a 1/4" - 20 bolt, the standard size for a camera tripod mount. This one is 35 mm diam. and 6 mm thick, plus a 3 mm shaft collar, but those are all parameters in the SCAD file. I had to ream it out a bit for the bolt to slide smoothly into...
thingiverse
... More information here: https://www.instructables.com/id/Body-Camera-Phone-Mount Tested with PLA and PETG: - 0.20mm layers - 20% grid infill - no supports - brim build plate adhesion It also works as a phone stand if you don’t mind blocking a corner.
thingiverse
A simple test for printing the thread for thread repair inserts for the 1/4-20 and 3/8-16 camera thread as well as the 3/8-16 to 1/4-20 converter. The threads have been tested to withstand in excess of 10kg without applying any fastening e.g. super...