camera phone tripod adapter 3d models
265432 3d models found related to camera phone tripod adapter.thingiverse
I had a camera tripod but couldn't use it with my telephone so I made this. ...Attaches to phone holder of this print and camera adapter on your tripod holds it perfectly
thingiverse
I needed a to use my wife's phone on a camera tripod, so I made this adapter to attach a cheap vent clip phone holder to a camera tripod. My wife thought it worked great, and she even decided to use the phone mounted so that the screen was against...
thingiverse
it fist the universal tripod/camera screw. i made the model close to another model found on thingaverse but this has the desired hole mount in the bottom. infill : 15% or higher its also fits my camera figrig!! check out if wanted cinematic...
thingiverse
This is a smart-phone camera holder for a tripod. It is designed to fit a nut that fits on standard tripod screws. Two kinds of nuts are supported, standard and one with an attached washer. The attached washer provides a bit more strength than a...
thingiverse
This is a small extendable cellphone camera mount for any tripod. The mount attaches to a standard 1/4-20 camera screw. The mount is designed to be self-tapping. The mount is custom made for my iphone XR with it's case. The case makes the phone...
thingiverse
TRIPOD_SIDE_3x TRIPOD_CENTER_2x TRIPOD_PAD_3X (roller 8 to 10mm) 1m aluminium round profile 10mm diameter
myminifactory
The design of this spare part was request using our “Request a Spare Part” form Here Sony sports cameras need an adapter to attach to a standard tripod screw. It can easily be lost and quite expensive to buy. Here is a functional 3D printable...
thingiverse
This is a standard sized adapter to put on any tripod to allow you to secure your phone to it. Insert The screws threaded side first into the unthreaded holes. Screw the piece with unthreaded holes to your tripod. ...Use the long screws to move the...
myminifactory
This design, paired with a heat set 1/4" hex nut, quickly becomes an easy, pocket-sized adapter to mount your smart phone to most standard tripods. ...Printed easily without supports.
thingiverse
Tripod adapter with standard thread to place the phone as a camera. It is required to have a broken one to be able to assemble it completely since only the structure of the object is printed. ... It is recommended to print it at 45º for greater...
thingiverse
wanted a small tripod to hold up my camera, had this old one from my blue snowball mic. ... Currently using a #8 bolt holding it together.
thingiverse
Super simple cradle for a phone so that it can be mounted to a tripod. ...Setup so you can mount phone to a tripod.
thingiverse
My Kids wanted to use the iPhone on our camera tripod, therefore I designed a simple cheap phone adapter which works well. I was originally going to make this spring loaded, but after putting it together it grips the iPhone 11 well with its cover. ...
thingiverse
This simple tripod phone adapter will have you shooting better stills and videos on your phone in no time! Fits most smartphones on the market right now. All you need is a small SAE nut with the following dimensions to fit the screw on your tripod:...
thingiverse
This should work with any smart phone but make sure it will fit your tripod I have designed this to where you can fit you're smart phone landscape or portrait. ...enjoy!
cults3d
Phone Holder for tripod The supports are available for 2 sizes -1.2 cm and -1.5 cm for each of the sizes there are 2 versions The first: a screw-on version compatible with all tripods that have a Kodak screw (most tripods) The second: clip-on version...
thingiverse
This is an initial attempt at creating a basic JeVois camera module mounting plate that will fit common tripods and 1/4" UNC bolt fixings. I used the mounting pattern from http://jevois.org/doc/CaseMounting.html - the official documentation state...
thingiverse
I have a selfie stick tripod, this adapter creates a platform to hold my binoculars. ...It does the job but won't prevent binoculars from accidentally falling.
thingiverse
Didn't see any tripod mounts on here that have the 1/4 screws for this. ... May need some pressure while screwing on the first few times
thingiverse
Fits to mini tripod and has a slot for phone to sit in, nothing more magic than that. Printed in two halves for speed/no supports. ...The two shells snap together.
thingiverse
This is a 1/4 tripod mount for attaching something with Velcro straps. ... I used it to attach a wireless HDMI extender to the output jack of a DSLR.
thingiverse
You'd also need an M5 nut. ...The thread (1/4") is a little tight, it's easier to screw on and off with the camera attached.
thingiverse
Custom Tripod mount for cell phone. This was made for my galaxy S6 with printed case to fit snug in the holder horizontally. Uses 10-32 screw and nut to hold bracket to base. 3/11/19 Added a threaded bottomed version to fit 1/4 20 SAE...
thingiverse
Small adapter for 58 - 75mm wide phones. Large adapter for cellphones 70mm wide and wider. Print it with no support. 0.2 layer height. 25% infill 0.1 layer height for bolt and nut. 100% infill. Threads will be tight. I had to use wrench on nut...
thingiverse
Simple phone holder for camera tripod. ...Made it for Huawei P9
thingiverse
Not quite a remix, but credit where it's due, I reused the nut and screw from: https://www.thingiverse.com/thing:2070272 I wanted a decent clamp to attach my mobile to a standard camera tripod. I needed a new 3D design challenge. This is the result.
thingiverse
I designed this camera/phone stand to help me film my projects, the design is fairly heavy duty and meant to fit with the threading on my olympus camera while at the same time is collapsible and can become fairly compact. To assemble it you'll need...
thingiverse
I've made an adapter for the Samsong Meteor microphone to place it on common camera tripods. The fit of the thread is pretty tight but fits well. ... 5/8-27 male to 1/4-20 female The f3d file is also available if someone wants to modify or improve...
myminifactory
Simple adapter to turn ski pole into a camera tripod. Works well for selfies :-) It does not use tripod screw mount but rather simple dock for quick installation. Camera adapter is designed for Panasonic Lumix LX3. Ski pole attachment should fit on a...