camera platform 3d models
135030 3d models found related to camera platform.thingiverse
This is a camera platform to support a webcam on a GoPro suction cup mount. ...This can then be mounted to the door of the MakerBot.
thingiverse
I've designed this frame for racing with a camera platform with gimbal. THIS IS STILL WORK IN PROGRESS !! STUFF WILL CHANGE !! Still working on the landing gear... The frame size is 340mm. Motors: Emax RS2205 2600kv. ( you really need a battery that...
thingiverse
A camera platform for the RasPi camera. Only the platform needs some support for the “teeth”. Created using Fusion 360, with thanks. For the camera case. I have used the following: thing:1646474 https://www.thingiverse.com/thing:1646474 Update: I...
prusaprinters
An extrusion-mounted universal camera platform for the MK3S+ (or anything with a 3030 extrusion rail).Fully reversible to work on either the right or left hand sides, and can be slid forward/back along the extrusion to taste based on desired camera...
prusaprinters
It did work very well for positioning a camera with Velcro to keep an eye on the 3d printer with Octopi. Print Settings Printer Brand: Monoprice Printer: Select Mini Rafts: Doesn't Matter Supports: Yes Resolution: 0.175 Infill: 50 Filament: AMOLEN...
thingiverse
This started out as a wig rack which could be placed over a air vent but it turned out my daughter wanted something else. ...It did work very well for positioning a camera with Velcro to keep an eye on the 3d printer with Octopi.
thingiverse
This is the combo battery box and FVV camera platform for the fusion2 Quadcopter. ...Measurements are X 3.789 in Y 1.113 in Z 7.501 in
thingiverse
This is a camera platform that only attaches to the y-rod assembly of the Lulzbot AO-101 3D printer. It uses the same bolt holes and nuts in the T-Bar frame. You will be required to swap out the hex bolts currently there for longer ones to make sure...
thingiverse
Small platform to allow mounting a micro-sized camera further forward in the frame so the camera doesn't see the roll cage.
thingiverse
A simple platform for the front of the lower plate that uses a rubber band/hairband to both secure the mount in place and hold the camera on too. The print is upside down so the tallest part is the piece that pops through the bottom and holds the...
thingiverse
I also made a larger platform that can move the camera further away from the print area if your webcam requires that or so you have a bigger surface to clamp just about anything onto. I have a Microsoft LifeCam that has a tripod mount point and used...
pinshape
I also made a larger platform that can move the camera further away from the print area if your webcam requires that or so you have a bigger surface to clamp just about anything onto. I have a Microsoft LifeCam that has a tripod mount point and used...
thingiverse
The motor can have any wheel attached to it and over that (or perhaps hanging from it when in upside-down position) any object to be photographed by IR remote controlled systems camera. I made software available at:...
thingiverse
Since almost all camera and webcams can be mounted on a tripod this will accept nearly all cameras made. The screws to hold this platform in place are M4. Replace the existing M4 screw that is used to tension the Y Axis belt with one that is 10 mm...
thingiverse
Simple mount that is convex on one side to form to the helmet curve, and flat on the for flat action camera base. Apply with a good double sided adhesive tape. ... enjoy!
thingiverse
I use a Wansview Q5 camera to monitor my 3D printers but wanted to raise it up to get better views. I tried to remove as much of the base block as possible but still maintain some sort of style. ... Printed at 0.28 in PLA with tree supports (Cura...
youmagine
The remaining hole will receive a M4 x 15 mm screw and nut to affix the camera platform. The tabs are to assist in preventing twisting. Print with at least 20% infill and upside down. ...It will print with no supports.IGES and STEP files included if you...
thingiverse
This is a camera tilt platform that encloses a naze 32 board and a servo, therefore requiring only power (from gopro 5v port) from the Vortex. As the Vortex does not have any tilt outputs, I had to use a separate Naze board. You can configure the...
thingiverse
Platform for an Afidus ATL 200 time lapse camera. ... Has a hole for tripod screw in the middle, raised lip on two side so you can place the camera back exactly where it was after replacing the batteries for extended shooting.
thingiverse
This is a mounting platform for a standard camera with a standard 1/4" screw attachment. I made the hole for the 1/4" screw so that you had the choice of tapping it for a 1/4-20 thread, or using a camera screw with a non-threaded through shaft with...
thingiverse
This is a 6 axis cnc motion controlled camera system I designed. I built this to help film stuff for my new YouTube channel. "doitwhenever?" check it out! ... I have a few videos up on how this rig works ...
thingiverse
This mount attaches to the underside of 2020 extrusion and the weight of the camera holds it in place. Easy to move left-right with a slight lift of the mount. 3 holes for 1/4-20 bolt (included) so you can position for best distance from rail. ...
thingiverse
I don't have a Mobius so I wanted to create a platform to hold my SJ4000 in place. If any other cam has the same dimensions (length and width), it should fit of course :) I use a scorpion strap to hold it in place. Be carefull the strap is not in...
thingiverse
This is quick-release platform for the Velbon CX-586 tripod. The tripod usually comes with only one of these in the package, but I needed a second one form my phone holder. The original one has a crock base and a retention pin. This design...
thingiverse
This is for raising the position of a Wyze camera while mounted on the front of the Sunlu S8 Printer. There are cable loops to hold the line power cord securely. I mounted this originally with a piece of double-sided mounting tape on the front of the...
grabcad
This is quick-release platform for the Velbon CX-586 tripod.The tripod usually comes with only one of these in the package, but I needed a second one form my phone holder.The original one has a crock base and a retention pin. This design omits the...
thingiverse
All platform hardware can be accessed from the top and can be removed without disassembling the quad (unless they get covered by electronics etc.) Updated 11/12/14: redesigned to removed overhangs on camera platform and added front/center hardware...
thingiverse
My latest attempt for a camera mount platform for my TP-Link IP camera. This mount keeps the camera stationary - but still gives a good view of the print process. ...Print Settings Printer Brand: Robo 3D ...
thingiverse
Volantex Ranger 2000 camera mounting platform. allows you to replace the battery without moving the video transmitter or camera. for the hinge I used a 3mm carbon rod. for the door lock spring I used a pen spring. all the pla parts were glued...