candy dispensor 3d models
5333 3d models found related to candy dispensor.prusaprinters
(pour le français, voir plus bas)Top support for candies dispensor.SettingsNozzle: 4mmResolution: 0.1mmInfill: 15%Rafts: noSupport: yesDuration: ~1h15Printer: Prusa Mini+ https://shop.prusa3d.com/en/66-original-prusa-miniMaterial:...
thingiverse
The dettol dispensor get's out of order when it's placed on a wet surface (water-condensation on the sensor) . ...Using this tablemounth fits fine and works perfect.
myminifactory
Nespresso box dispensor turns the box your coffee capsules come in, into a handy counter top dispensor. ... Simply cut the perforated lid off the box and insert the box into the dispensor.
3docean
3D model of Candy Environment, materials, lights, render settings included, Global illumination render settings
thingiverse
... http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519 Instructions Using the following options: Your_Text = CANDY Text_Rotate = 0 Text_Size = 11 Text_Font = write/knewave.dxf
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: hole_radius = 2 Font = write/orbitron.dxf stick_thickness = 3 message = Candy font_size = 15 font_thickness = 6 stick_width = 8 flat_bottom = 1
3docean
Please don’t forget to rate the model, for us it is very important 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene Statistic below: Polys: 12 399 Tris: 12 400 Edges: 18 641 Verts: 6 243 - Scale of...
thingiverse
TAPE DISPENSER FOR 3 INCH ROLLS. WITH A PIN HOLE FOR WIDTHS LESS THAN 1" AND ANOTHER FOR LESS THAN 2". IT IS MADE TO HOOK TO YOUR BELT LOOP OR PANTS POCKET. THE SMALL HOLES ARE FOR A PIECE OF WIRE TO THREAD THROUGH AND RETAIN THE ROLL. THE STRESS...
thingiverse
I designed this simple contact dispenser because I hated having to grab them out of the box every time. I have only tried these with Proclear 1-Day's but I think they should work with other lenses. ... The lids aren't needed and are very loose but I...
thingiverse
(work in progress works with minor trimming to certain areas) (scale dispenser.stl to inches from mm) this silly dispenser thing I made up to test my new printer, it uses a sg90 servo to spin little paddle wheel inside to dispense treats, with a...
thingiverse
Customized version of https://www.thingiverse.com/thing:4808156 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4808156
thingiverse
Customized version of https://www.thingiverse.com/thing:4808156 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4808156
thingiverse
Customized version of https://www.thingiverse.com/thing:4808156 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4808156
cults3d
Sized to fit your favorite 30 mm plastic bottle cap. Bushing will allow use of caps around 27 mm. 150 mm base is a little more than a 2 hr print & will provide more stability. Requires 2 holes in the side of the cap. Remove the security ring...
thingiverse
This small hand held sugar dispenser is designed to be held with one hand, while the other rotates a large tactile knob to dispense a 1/4 teaspoon of sugar into a coffee or tea. The sugar dispenser is 100% 3D printed, there are no other parts or...
thingiverse
Sized to fit your favorite 30 mm plastic bottle cap. Bushing will allow use of caps around 27 mm. 150 mm base is a little more than a 2 hr print & will provide more stability. Requires 2 holes in the side of the cap. Remove the security ring left...
thingiverse
This is a spare glas for my HEWI Soap dispensor. the orginally was from glass and it was broken. No spare availiable at the market. Now printed in three parts. Optimized with a stand plate, designed for a spare soap pump from the market. glued...
thingiverse
The dettol dispensor get's out of order when it's placed on a wet surface (water-condensation on the sensor) . Using this tablemounth fits fine and works perfect. This is a new HOVER-design With the refillnut you can easely refill you soapdispensor...
cults3d
Candy box, flower pot, object holder, whatever you want from the Buu. ... Use very few holders three versions, one complete, in one piece and in parts Candy box, pot, object holder, whatever you want from Buu. ... Use very few supports.