canopy for betafpv meteor 65 by 3d models

For BetaFPV 65 series!

65_lightweight canopyM3 VTX can be installed

For BetaFPV 65series!

For BetaFPV 65series!

This is a remix of a canopy for Nano Camera Whoop Edition, to be used in BetaFPV frames, that can hold an Insta360 Go2. ... Original design: https://www.thingiverse.com/thing:4357958 The holder can be downloaded from: ...

Racing canopy for "HGLRC Batman 220" drone frame. This canopy is only compatible with the micro camera series (L19mm*W19mm).

This is a remix of the Angry canopy by AngryDon. This is extended in the rear and has a hole that fits a vtx dipole antenna. ...This was made to fit the Litejay by Rotorgeeks.

I'm a beginner so just lengthened the original canopy, added a front screw hole inside and set a BN-220 GPS holder on top. I've got minor flaws but it can be printed with supports easy. ... Beta85X frame: https://ali.ski/d4t_j RunCam Hybrid 4K cam:...

Adapts NewBeeDrone 75mm Cockroach frame to fit BetaFpv HD Canopy or other similar screw hole canopies.

I was looking for a carrying case for my BetaFPV Meteor 75 Pro FPV Quadcopter that holds my drone as well as accessories like batteries, charger, tools, props and a powerbank. Since this is very specific, I didn't find anything out there that met my...

This canopy is designed specifically for 65mm frames. Since I only have access to smaller frames, there's no design available for larger ones. You can modify the step files using your preferred CAO software. Alternatively, you may find it easier to...

BonjourRemix de Auvent Whoop à angle réglable [Remix de Tiny Whoop - Mobula 6 - Canopy].Cette canopy est génial.J'ai désépaissie pour la rendre un peu plus flex et que la camera soit plus simple à rentrer.J'ai aussi fait en sorte que le tpu ne soit...

Needed an Clip on Battery holder for my 1s 520mah for betafpv65. standart there goes 1s 300mah sticks. ... ...New tighter version (520neu)

Here's a canopy design tailored specifically for the BetaFPV Hx100 drone. I've dubbed this creation the "Baby Dragon" in recognition of its compact yet robust build. ... Key Features: * Designed to optimize airflow around the motor and propellers *...

Canopy for the famous betaFPV HX115 HD It is made to mount a pandaRC vt5804_AIR in it. I added a Lumenier Micro AXII Shorty to it as well :-) You need some support to print it. ...I made mine from TPU.</p> <p>Happy printing and flying ;-)</p>

A replacement nozzle for the Dynam Meteor 70mm jet. ... It is generally based on the nozzle of the Supermarine Swift, to which the Dynam Meteor has a passing resemblance if repainted.

... Insta360go Mount Print: The mount was printed using TPU filament, which provided excellent flexibility and durability. Custom Canopy Print: In contrast, the canopy was printed with PETG filament, offering superior rigidity and resistance to impact.

Custom elevated canopy designed to seamlessly integrate the Caddx Turtle V2 and original VTX from the HX115. ...Requires cutting at the cutter to allow for insertion of the protective lens cover (Caddx Turtle V2 Lens Protection Hood).

Here is a custom-made frame designed specifically for the beta75X or Beta85X drone, optimized for superior flight performance with either 40mm props or 2-inch props. To convert between prop sizes, you'll need only a few stand-offs and long screws to...

However, its potential soon had it evolving into a compact Meteor Flail perfect for transforming figures. Fair warning: due to the small size of this piece, it will only work on resin 3D printers unless scaled up. This design features interlocking...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: Teeth count is set to 65. The distance between the nut shaft and the retainer HT is 1.2 mm. No additional tooth depth has been added. M3 bolt...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: motor_shaft = 20 no_of_nuts = 1 m3_dia = 3.2 pulley_b_dia = 20 idler = 0 m3_nut_depth = 2.7 retainer_ht = 1.5 profile = 2 nut_angle = 90 teeth =...

... which features magnets to secure its position. To address this issue, I developed the Handle as a separate component that can be easily attached to the top of the canopy using adhesive, allowing for effortless opening and closing of the device.

I've got a Betafpv 75 Pro 2 and was searching for an awesome gate to build a race track at home. I used Transparent PLA to print it, and added some LEDs to make flying at night even more fun. So I created this gate. ... If you'd like to help me out,...

https://rotorbuilds.com/build/30190 There is also a new mod for flying upright: https://www.thingiverse.com/thing:5536503 https://rotorbuilds.com/build/30483 --------------------------- In early 2020 I designed the first pusher mod for the meteor...

Because the lipo is on the underside, sometimes it's hard to get the quad sitting flat on it's starting place. These feets should help :-) The weight of 4 feets is less than 8 grams The light ones are around 4 grams. Not the easiest thing to print...

\r\n\r\n3) Added braces to the Caddx Turtle mounting standoffs to make it easier to screw in the Caddx Turtle PCB when using TPU mount, especially for users who prefer to use black screws and washers that came with Caddx Turtle instead of silver...

This model was created using Tinkercad. ...Modify it directly online at https://www.tinkercad.com/things/7h4CJ2aYxLg

Here is the rewritten text: These units are designed to be compatible with models E011 and others that have a barrel diameter of 65 or 68 millimeters.

I really like the BetaFPV 4K canopy, but none of its mount holes align with any frames except for the Beta95x or Beta85x. When BetaFPV released a toothpick-style frame called the X-Knight 200mm Frame, measuring five inches in diameter, I wanted to...