capacitive moisture sensor 3d models

36915 3d models found related to capacitive moisture sensor.
Capacitive Moisture Sensor Housing
Capacitive Moisture Sensor Housing
thingiverse

This is a housing for a capacitive moisture sensor which i have now worked on for two months. One common problem of these sensors is that they arent enclosed/protected against water ingress. Because of that i have set out on the road of enclosing the...

Capacitive Moisture Sensor Raindrop Cover
Capacitive Moisture Sensor Raindrop Cover
thingiverse

For those that want a good looking cover to their Capacitive Moisture Sensor v1.2 vs a functional one. ...There are two versions of the bottom half of the cover, one that will allow the default connector to pass through and one for bare wires.

Capacitive moisture sensor v1.2 box
Capacitive moisture sensor v1.2 box
thingiverse

This box is for a enclosure the capacitive moisture sensor V1.2 electronic parts. ... I recommend to also use hot glue or similar product for 100% waterproof it.

Capacitive Soil Moisture Sensor
Capacitive Soil Moisture Sensor
thingiverse

[Capacitive Soil Moisture Sensor](https://github.com/RonMcKay/capacitive-soil-moisture-sensor) ======================== This is a capacitive soil moisture sensor which runs with a standalone ATmega328P and utilizes the...

Capacitive soil moisture sensor housing
Capacitive soil moisture sensor housing
thingiverse

A simple housing for the grove capacitive soil moisture sensor from Seeedstudio ([these](https://www.seeedstudio.com/Grove-Capacitive-Moisture-Sensor-Corrosion-Resistant.html)). ... Part of this [project](https://github.com/enwi/ESP8266-soil-moisture)

Crowtail Capacitive Moisture Sensor V2.0 case
Crowtail Capacitive Moisture Sensor V2.0 case
thingiverse

Four (4) enumerated cases for Elcrow Crowtail-Capacitive Moisture V2.0/V2.1 sensors. These cases are better fitting and don't need any extra trimming with a blade to fit the board inside. You'll need a total of 16 M3x8mm screws with countersunk...

Capacitive Soil Moisture Sensor Case
Capacitive Soil Moisture Sensor Case
thingiverse

Outdoor Case for Capacitive Soil Moisture Sensor v1.2 Remove the plug contact and solder the cable directly. Push the sensor into the housing and seal the passage with super glue. ... Fill the case with polyester resin and also coat the sides of the...

Capacitive Soil Moisture Sensor Cover
Capacitive Soil Moisture Sensor Cover
thingiverse

A very small cover for the capacitive soil moisture sensor. Designed for a cable with 3.4 mm diameter soldered directly to the sensor with the jack removed. I printed this with a Prusa i3 and had to scratch the edges with a knive a little bit to...

Capacitive Moisture Sensor v2.0
Capacitive Moisture Sensor v2.0
thingiverse

I took some inspiration from the original design and added a few features: - Thicker walls - Beveled edges for wire exit. - Added a cap to seal the bottom off. I printed the base with support structures and stood it vertically with the wire...

Capacitive Soil Moisture Sensor v1.2
Capacitive Soil Moisture Sensor v1.2
grabcad

Generic capacitive soil moisture sensor purchased from AliExpress.

Case for Capacitive Soil Moisture Sensor
Case for Capacitive Soil Moisture Sensor
thingiverse

Capacitive Soil Moisture Sensor V1.2 Case I designed a case for a Capacitive Soil Moisture Sensor. It fits nicely. Maybe a endcover is comming soon. ...

电容式土壤湿度传感器外壳-Capacitive soil moisture sensor housing
电容式土壤湿度传感器外壳-Capacitive soil moisture sensor housing
grabcad

一款电容式的土壤湿度传感器外壳,由一个底壳和上壳组成,可以直接使用FDM3D打印机打印出来。头上可以接一个直通管。A capacitive soil moisture sensor housing, consisting of a bottom shell and an upper shell, can be printed directly using a FDM3D printer.

Capacitive Soil Moisture Sensor v1.2
Capacitive Soil Moisture Sensor v1.2
thingiverse

This is a small box for the Capacitive Soil Moisture Sensor v1.2. Resin is needed for make it waterproof. For cabling I used a 3x0.14mm² flexible cable. ... UPDATE: I added the SCAD files.

Capacitive Soil Moisture Sensor V1.2 Housing
Capacitive Soil Moisture Sensor V1.2 Housing
thingiverse

Another housing for the capacitive soil moisture sensor v1.2. Just for covering the electronic parts, not fully waterproof because the socket remains on top. It's intended for inhouse use only. Two versions: 1st - minimum flat lid. 2nd - covers...

cover for Capacitive Soil Moisture sensor
cover for Capacitive Soil Moisture sensor
thingiverse

Cover for Capacitive Soil Moisture sensor https://www.amazon.it/dp/B07DDFZ3MD?ref_=cm_sw_r_cp_ud_dp_6RX71C3XNRJ7X19JS65C Bolts M3*8: https://www.amazon.it/gp/aw/d/B073ZV8GW3?ref=ppx_pt2_mob_b_prod_image# If you like it ;)...

Capacitive Soil Moisture Sensor with ESP8266
Capacitive Soil Moisture Sensor with ESP8266
cults3d

Capacitive Soil Moisture Sensor, based on ESP8266 (Mini D1) and 1$ sensor. This module run ESPHome, and connect to Home Assistant. Sensor is plugged in Analog To Digital converter. ... Material: - ESP 8266 d1 mini :...

Capacitive Soil Moisture Sensor with ESP8266
Capacitive Soil Moisture Sensor with ESP8266
thingiverse

*********************************** Capacitive Soil Moisture Sensor, based on ESP8266 (Mini D1) and 1$ sensor. It runs with 1x 18650 in deep sleep, with wake up every 2 hours. This module run ESPHome, and connect to Home Assistant. Sensor is...

Slim Cover for Capacitive Soil Moisture Sensor
Slim Cover for Capacitive Soil Moisture Sensor
thingiverse

The soil sensor can be purchased on AliExpress: 10 Pieces Capacitive soil moisture sensor V1.2 I used the following sealant around the edges of the edges of the sensor: Adhesive Sealant Fix I used the following sketch. I recommend conducting your...

Capacitive Soil Moisture Sensor v2.0 Cover
Capacitive Soil Moisture Sensor v2.0 Cover
prusaprinters

Outdoor cover for the popular analog Capacitive Soil Moisture Sensor v2.0.No soldering changes are required. I just crimped a JST 2.54 mm female connector on the cable. The cable diameter is 4.6 mm (3 cores, 22AWG), but the hole in the cover is...

cover for capacitive soil moisture sensor v2.0
cover for capacitive soil moisture sensor v2.0
grabcad

capacitive soil moisture sensor 2.0

Case for Capacitive Soil Moisture Sensor v1.2
Case for Capacitive Soil Moisture Sensor v1.2
thingiverse

Case for Capacitive Soil Moisture Sensor v1.2 Sensor width was 23,10mm

Case for Capacitive Soil Moisture Sensor v1.2
Case for Capacitive Soil Moisture Sensor v1.2
cults3d

Case for Capacitive Soil Moisture Sensor v1.2 Sensor width was 23,10mm

Case for capacitive soil moisture sensor
Case for capacitive soil moisture sensor
thingiverse

A simple and quick housing for a capacitive soil sensor (v1.2). Glue it together how you like (hotglue?). ... Size: 28x26x11mm Wall thickness: 2mm Freecad file included

Case for capacitive soil moisture sensor
Case for capacitive soil moisture sensor
thingiverse

A simple housing for a common soil moisture sensor. Assembly: Insert the sensor into the main body, push the cable through the hole in the cap and close the case. Glue it shut how you like and apply a coat of water resiting spray. Print standing...

Case for capacitive Soil Moisture Sensor
Case for capacitive Soil Moisture Sensor
thingiverse

for capacity sensor with analog out

Capacitive Soil Moisture Sensor 1.2
Capacitive Soil Moisture Sensor 1.2
thingiverse

Small changes to the original to fit the sensors from China.

Capacitive Soil Moisture Sensor v1.2 - Remixed
Capacitive Soil Moisture Sensor v1.2 - Remixed
thingiverse

https://www.thingiverse.com/thing:2952434 didn't quite fit my sensor and it didn't used the connector that came with it. Remixed it to be a bit wider and added space for the connector. I also moved both designs in one file and added a bunch of...

Surface Box Base for Capacitive Soil Moisture Sensor
Surface Box Base for Capacitive Soil Moisture Sensor
thingiverse

Surface Box Base, for Capacitive Soil Moisture Sensor - Works on Solar. Project: Work in Progress. ... https://thingspeak.com/channels/1050909 https://christiankronen.de/solar-bodenfeuchte-sensor/

Capacitive Soil Moisture Sensor V1.2 + DHT22 Sensor Case
Capacitive Soil Moisture Sensor V1.2 + DHT22 Sensor Case
thingiverse

A quick remix of the “Capacitive Soil Moisture Sensor v1.2” case with the added feature of having a screw hole for mounting DHT sensors. ...The hole is 3,5 mm wide and fits an M3 x 8 mm screw.

House Case for the Capacitive Soil Moisture Sensor V1.2
House Case for the Capacitive Soil Moisture Sensor V1.2
thingiverse

A simple enclosure in two parts for the Capacitive Soil Moisture Sensor V1.2 https://www.amazon.fr/gp/product/B07R174TM1/ https://www.aliexpress.com/item/32832538686.html No support needed. ... Can be finalized with glue (on joints and holes) to improve...