car charger and holder 3d models

This thing was created because my car charger and phone holder always hang down to low. ...This thing will support your car charger/phone holder to keep your phone higher as well as providing extra compartments for cards/pens/anything.

PLA 55 g Print Settings: 2 Walls 4 Top 4 Bottom 20 % infill 0,2 mm layer BOM: 1x printed part 2x bolt M3x20 2x nut M3 1x wireless charger like...

Nexus 5X car holder with charge connection This is a Nexus 5X car holder, which allows the phone to be used with the standard flip cover attached. And (optionally) allows the phone to be charged with the standard USB-C cable. The holder attaches to...

I was annoyed by having to messily put down my car charger on a shelf so I designed this to hold it. Fits perfectly for my Chevy Volt charger, not sure which other chargers fit but most should work. ... Shouldn't need more than 20% infill, and no...

Needed a car center console holder for my Anker charger. Remixed Bitterbuffalo's mount so it lays flat and made some cutouts for the charging cord. Seems to work for my Samsung. Also added a forward attachment to mount a pair of 40mm (or one 80mm)...

Holder for my Car charger volvo v60 D6 hybrid. ...will fit all mennekes charger of the same model.

... for RAV4 dashboard and this magsafe charger. ...Should fit other cars too. It could work with other magsafe chargers that use ball joint (this one has a diameter of 17mm).I printed it in two halves and super-glued them in order to avoid supports. 

Sepura car holder charger made for STP8240 -used D-Sun DC/DC Buck converter based on MP1584 adjusted on 10V (2A) -charge pins are taken from crimp BNC connector (center pin) -positive charge pin should be left when you look radio face. -pins are...

Vent clips use from original Car Vent Mobile Holder. Clips: ABS, PETG, PETG HTholder: PETG, PETG HTPrint seting: Nozzle: 0,4 layer: 0,2fill: 20%perimetr: 3x2.6.2022 - add Clips17.5.2022 - repair bug on car mobile holder 

Mobile phone and battery bank holder

Mobile phone and battery bank holder

I got tired of my phone falling off the charger so I printed up a fix.

It is a holder for your 3d printed parts

I designed this phone holder, you stick the charging cube in the square hole, then rest your phone on top, PRINT WITH SUPPORTS, print as shown

Simpel and small Battery holder and Charger Holder

This is a wireless car charger holder for the Nexus 6. The cup at the back is designed to hold the Powerbot charger perfectly and so no support is needed. Instructions This is designed to print with...

  The software I used to create the charger was Rhinoceros, I'm a fan of the Fast and Furious series, so it was enjoyable using it to bring one of the most iconic cars from it to life with my own personal replica. I used the skills I've built up...

Nexus 4 Car Holder with integrated hole for no-name wireless charger.(bought on ebay for 10 bucks !) All buttons and mic now reachable ! ( forgot the mic in first version, as seen on pictures ) I didn't make any locking system on the holder as i...

creations: https://www.thingiverse.com/thing:3692796 (Cable Flexi Charger holder) https://www.thingiverse.com/thing:3697980 (Cable Flexi Charger 3.2KW trick) https://www.thingiverse.com/thing:3704105 (ZOE 2016-19 SD card removal protection)...

Nokia Lumia820 Holder and Charger- Work in progress. ...Suggestions are most welcome.

This is a just-slide-in-your-phone car holder/QI charger I made for my Samsung S7 with thin protective cover AND designed for the connection on the one I already had. I was getting tired of plugging in my phone all the time. There are only 3 parts :...

This is a wall mounted holder for a battery charger for the Crescent Egoing electrical bicycle. One part to hold the charger (mains cable through the bottom hole), and one part for the battery. ...

Original design from : https://www.myminifactory.com/object/3d-print-cowboy-battery-and-charger-holder-177179 Designer : Machiel van der Schoot - @machielvanderschoot

... ... Replaces stock magnet with a holder for the Apple MagSafe charger for the iPhone 12.

Vape concentrate/oil cartridge holder for both 0.5g and larger 1g tanks, as well as an insert for the screw-on charger. ...Keeps everything in one place in as small a footprint as possible.

Adapter to have a cheap "Mobile Phone Holder, WSM-10L+TYPE P" - Windscreen Suction Model; Clas Ohlson part # 38-4251 (seems to be gone by now, *sigh*) hold a Nexus 7 - AND a feedly QI-charger under it...

This helps to hold the charger of any phone and helps to guide it into an outlet. 

To be wall mounted to collect the charger cable

Then the charger should go into the large slot with a light friction fit. Keeps the cord contained and the USB connectors clean. Print Settings Printer Brand: MakerBot ...

This is a improved version of my older design with space for a IKEA wireless charger Made for iphone 11 but will fit any phone with wide: 85mm thick: 12mm or smaller!