car radio faceplate case 3d models
313601 3d models found related to car radio faceplate case.thingiverse
This Radio case is designed for din car radios. It uses a 20v Trotec rechargeable battery with a buck converter to step down to 12v and a circuit which cuts power at 18v. It runs a little warm so you need a 60 mm fan. Speakers are 10 cm in diameter.
thingiverse
Car/Marine Radio Case for various sizes, don't have all kinds of radios so can't say if it will fit very deep radios This design uses 4mm connectors for speakers, XT60 for power and a hatch in the back for all other connections from behind the radio...
prusaprinters
case for din radio to stand free you need to add a negativ volume where you want the cableholehas printed it in Prusa ASA 0,2mm round about 14h remixed from https://www.thingiverse.com/thing:3853999/files
thingiverse
Simple case I've designed to accommodate a car radio recycled from an old Ford Fiesta, that I used to listen to music in my garage. ...Front aperture is standard size, so it fits (or should fit) any DIN car radio.
thingiverse
Radio Stack faceplate for the DIY Cessna 172 Radio PCB https://flyingforfun.weebly.com/cessna-172-cockpit.html/#Radio Update: 22.04.2018 Reworked everything and added more text.
thingiverse
I made a ADF-XPND Faceplate based on the Cadet Radio NAV and COM setup. (With permission) I just wanted to add the same style the original version. De difference is that this is with 4 normal encoders and one push button. The software is in...
thingiverse
A guy from the Alabama Historical Radio Society brought me in an old, broken plastic part from a 1937-ish Crosley AM Radio. The glass was cracked and so was the plastic. We located a brand new glass piece, but no dice for the plastic. So I...
thingiverse
2006 nissan 350z aftermarket radio faceplate replacement double den radio
thingiverse
I found a company that makes new configurable radios (http://www.retrosound.com/), but they didn't have a faceplate or knobs that matched my car. I designed an adapter that slides on the front of the radio that is close to what the original radio...
thingiverse
This is a faceplate for the 2020-2022 Toyota Tacoma Radio. This replaces the original screen radio with 2 single din slots. Take the old radio out, install an aftermarket radio or two into this, and place it where the old radio was. I have not...
thingiverse
Adapter for insert 1DIN radio to 2DIn slot in Ford Mustang 2005-2014
thingiverse
Used extension cables to go from the faceplate to the connected device so radio bezel is easily removeable Hardware: USB 5Gbps (USB 3.0, USB 3.x Gen 1, Superspeed) Cable C Female to C Male 0.48' (146.1mm) Shielded digikey part number:...
thingiverse
Removed top dome, transferred the hole pattern to top surface, remove the side text, added two large holes in the back for easy management of power and audio cables, left some space in the front of top surface in case you want to emboss your custom...
thingiverse
Then you can either use the same type of screws used to mount the LCD, or use screws that are long enough to go right through the case and mount faceplate and lcd using screw and nut. The cutouts for the speaker, dial knob and reset button are one...
thingiverse
Simple model but took me a few goes to get the dimensions just right so it fits well but not too loosely or too tightly. ...The radio is in my Mazda Bongo campervan so added a Mazda logo for effect. ...Printed on a glass sheet for a nice smooth finish.
thingiverse
This is my second and much improved version of an Anbernic rg351v case. It snaps on to the sides. You are gonna want your bed leveling on point for this one. If your bottom layer has gaps the lip that holds it on will break off. if you are too close...
thingiverse
Чехол подставка для пульта магнитолы JSD-3001. Я закрепил в багажнике на двусторонний скотч, чтобы не бегать к магнитоле жать на кнопки. Предусмотрены места для саморезов. Вкладывать кнопками внутрь. ...Печатать с поддержками.
thingiverse
mount your car radio to the wall with 12v china power supply and plug in your subwoofers to both
thingiverse
Button for a car Radio Print Settings Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: No Supports: No Infill: 25%
thingiverse
I have replacement radio buttons for the original Audi car radio here. One button has a 6mm inner circle, the other 8mm. I printed with a resolution of 0.1 or 0.2mm, you can vary the infill between 20 and 50%. I used TPU filament. Have fun...
myminifactory
For this car radio manufacturers have made a removable front on there car radio's with the idea that the radio has no value without them. This would then prevent that the radio will be stolen. But unfortunately after a while the contacts between the...
cults3d
For this car radio manufacturers have made a removable front on there car radio's with the idea that the radio has no value without them. This would then prevent that the radio will be stolen. But unfortunately after a while the contacts between the...
pinshape
For this car radio manufacturers have made a removable front on there car radio's with the idea that the radio has no value without them. This would then prevent that the radio will be stolen. But unfortunately after a while the contacts between...
thingiverse
For this car radio manufacturers have made a removable front on there car radio's with the idea that the radio has no value without them. This would then prevent that the radio will be stolen. But unfortunately after a while the contacts between...