card dice 3d models
81967 3d models found related to card dice.thingiverse
New format Batman Miniatures Game character card & dice holder. Main area is sized for the card in a 3.5" x 2.5" sleeve. ...Lower area keeps 12mm dice in line with the Move, Attack, Defense & Special categories.
cults3d
Just a fun, little kit card dice tower I designed. Functions pretty well and would make a neat stocking filler! ... Available in 2mm and 2.2mm thickness, I found with my printer that the 2.2mm give a better press fit together than the 2mm version (the...
thingiverse
Minimal design dice tower made out of playing cards with 3D printed joints. ...The tolerances on this are about 0.3mm (playing cards are about 0.05-0.1mm thick) so I'd recommend starting with the middle bottom piece as it is the smallest, if you can fit...
cults3d
Minimal design dice tower made out of playing cards with 3D printed joints. ...The tolerances on this are about 0.3mm (playing cards are about 0.05-0.1mm thick) so I'd recommend starting with the middle bottom piece as it is the smallest, if you can fit...
thingiverse
Slide off case for your deck of Pokemon TCG cards. My photos are terrible because my printer is junky, but even with a junky printer it is totally usable. I only used supports for the "Top" portion. ... Have fun!
cults3d
This Combined Card Holder Dice Tower was designed for awesome RPG boardgame Karak, but could as well be used for Carcassonne and other games that uses cards or dices. It's created for regular 45x45mm cards (I guess its 1 and 3/4") with capacity of...
thingiverse
Holder for: - 40K Datacards, 36 Dice and the Gamesworkshop Tapemeasure. ...
cults3d
The one in the photo is the original design, I have since revised it to fit the dice better and made the finger holes bigger so it is easier to get the cards and dice out. I assume this will work in other boxes, or just as a general holder, so the...
thingiverse
The one in the photo is the original design, I have since revised it to fit the dice better and made the finger holes bigger so it is easier to get the cards and dice out. I assume this will work in other boxes, or just as a general holder, so the...
thingiverse
Organizer for the cards and dice of the Mice and Mystic boardgame. This was designed for the german version - I don't know if the sizes are the same for others. I included a space for two extra dice and saving filament ;) Hope you enjoy and would...
thingiverse
*I have no affiliation with Fabula* I recently backed Fabula Storytelling Cards for Kids on Kickstarter, and decided to knock up a quick die. It's nothing fancy, but it does the job! Sorry for the horrible photo, it's late. No supports...
thingiverse
This is a remix of the lid for the HeroQuest Card and Dice Box with Sliding Lid by bitr0t. ...
cults3d
Card and dice organizer for Altoids tin Can hold up to 30 cards (45 mm x 32 mm) in each card tray slot. ...Dice tray can hold 8 sets of 6 dice (5 mm)
thingiverse
Card and dice organizer for Altoids tin Can hold up to 30 cards (45 mm x 32 mm) in each card tray slot. ... Dice tray can hold 8 sets of 6 dice (5 mm) I'd upload more pictures but I sorta lost the tin...
thingiverse
I made this based off a design I saw somewhere else, Its just a box to hold the items/spell cards or dice for my D&D players, I used different colour combinations for different classes. Tolerances are pretty tight so it doesn't slip. I designed the...
thingiverse
This card and dice holder replaces the original one from Zombicide (Season 1). The original was flimsy plastic, wasted a lot of space, and didn't have room for expansions. This model: * Fits in the original (Season 1) box in place of the original *...
3docean
Ace of Spades with King of Spades Playing Cards & Dice on Black Surface
thingiverse
But I wanted a dice drawer and a separate divider for some extra cards as well! You can buy a deck box that has those, but those are usually way larger in size. Just print this divider and slide it into your deck box. +The largest compartment is...
thingiverse
The smaller case can hold the small drawer, one non-sleeved set of Pokemon cards, and a dice tray. There are two dice trays. Either dice tray can fit in either case. One holds a single set of damage counter dice (6), a single coin dice, and two...
thingiverse
Perfect solution for that one friend who always rolls their dice completely across the table, bringing with them a path of destruction to all cards and characters along their way. ... And if you like Talisman make sure you check out my other Talisman...
thingiverse
This holds all large cards included in the base game and fistfull of extras, and good bad and handsome expansions -- poker deck, event cards, man in Black, and bandit cards. This likely won't fit sleeved cards. It also has spots available for the...
cults3d
Here is a support for a card game and dice. I made this support for a game I made, the Rixe Marseille. ... More information here (in French): https://ouiaremakers.com/posts/tutoriel-diy-comment-faire-son-propre-jeu-de-societe-comme-un-pro-rixe-marseille...
thingiverse
Magnetic Dice Holder Modeled after Ultra PRO dice holder. ... Simply print 2x, and use magnets from Home Depot https://www.homedepot.com/p/Magcraft-Rare-Earth-1-4-in-x-1-16-in-Disc-Magnet-80-Pack-NSN0657/204721317
myminifactory
This object was made in Tinkercad. ...https://www.tinkercad.com/things/3LVIDreo15e For halloween comp. This spellbook was designed for Magic The Gathering cover opens and compartment inside folds out to hold cards upright
thingiverse
Customized version of https://www.thingiverse.com/thing:2404395 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2404395
cults3d
The idea was to cover Magic the Gathering with standard decks of 60 + 15, UNO (thought I don't have it and could not test it), standard deck cards, and some other random sizes to put dices or whatever. You have 3 dividers for box which allows you to...
thingiverse
A box for card and dice for the game Star Wars Destiny 28-12-16 /!\ Up grade pivot cover / box
thingiverse
It has room for all 8 of the original dice and enough space for sleeved versions of all of the original cards. The box and lid are designed with angles that do not require supports while printing. The lid may be a bit tight after first printing,...
cults3d
Holds all of the tokens, dice and cards which come in the Warcry Catacombs set. Magnet ready - just glue in four 6x1.5mm magnets. The base is 178mm long, 122mm wide and 68.5mm tall. The lid is 178mm long, 122mm wide and 55.5mm tall. ... Comes with two...