case designed for the papilio pro fpga development board 3d models

A case for a 4 port (2 NES, 2 SNES) hub for Mick's (https://github.com/MickGyver) Daemonbite adapter for the MiSTer FPGA To get all 4 ports working correctly from 1 Arduino you will need to use this modified source as well. Those you can restore CDC...

Lolin NodeMCU V3 dev board, pins are 0.1" (2.54mm) pitch with a 1.1" (27.94mm) wide footprint. ... Commonly found on Ebay, etc.

Remix of "Ports" part of MiSTER FPGA + I/O Board and USB HUB by onaluf (November 02, 2020) with modified MisTer USB Hub v2.1 power port, wich is USB. ... For my ordered USB Hub need to resolder Micro USB OTG adapter to make it longer.

This enclosure is designed specifically for the USB-Digispark, paired with an outgoing cable that's approximately 4mm in diameter. To secure the cap and cable effectively, you'll need to use zip ties measuring 2.5mm wide. Additionally, the status of...

This is a scalable Bearingholder with line guide designed for the hanging Printer from Torbjørn Ludvigsen at [email protected] Visit http://www.appropedia.org/Clerck,_a_RepRap_3D_printer_hanging_from_the_ceiling to learn more. ... Printer Settings:...

This is a highly versatile Bearingholder with line guide designed for the hanging Printer created by Torbjørn Ludvigsen at post@ludvigsen3dprinting.com. Visit http://www.appropedia.org/Clerck,_a_RepRap_3D_printer_hanging_from_the_ceiling to learn...

Minimalistic case for Arduino pro micro. You can use tape or tape to secure the base and cover together. ...I used white electrical tape.

MakerHawk ESP32 Development Board WiFi with 0.96inch OLED Display WIFI Kit32 Arduino Compatible CP2012 for Arduino...

You can use this dummy to construct your own case for a RunCam Pro.

I DESIGNED THIS CASE EXCLUSIVELY FOR MY MTE 10 PRO, FEATURING AN ACCURATE ADJUSTMENT SYSTEM THAT MAKES IT EASY TO INSTALL AND REMOVE AT WILL, WHILE THE SPEAKER IS POSITIONED IN A CONVENIENT LOCATION AT THE FRONT TO PREVENT OBSTRUCTION BY THE HAND.

I'm working on a two-part casing project for my TTGO Esp32 development board, but I still have some work to do before it's complete. In fact, I've already repurposed two of the buttons for another project, so I'll need to update this model once my...

More resources for electronic engineers:https://nmtelectronics.com/product/ai-thinker-nodemcu-32s/

I couldn't find this anywhere so i made my own for my project. Hope it's usefull . ...It's not 100% but it's close enough to be useful Made in solidworks 2020

This is a case for the BTT SKR Pro v1.2 to be side mounted on ender 3 (Left side) You will need to mount the stock ender 3 screen to this case since the wires don't reach the screen original location. I designed a cover but still need some...

My simple case design for main board GRBL CNC Engraver / router. ...There are holes for 50mm FAN for cooling step drivers.

This laptop casing is precisely designed to fit a Lenovo u430p ideally, allowing for about 0.25 inches of extra space around it. ...The dimensions are expressed in standard units, which makes the sizing process incredibly straightforward and accurate.

The OctoPi case is specifically designed to fit onto the RPi 3B+ and V2 camera, while also being mounted securely onto the Ender 3 Pro X-Axis tension plate. This particular design relies heavily on brass inserts in order to hold everything together...

I'm rewriting a Remix from the Omnibus F4 V3 Pro housing, designed specifically for use with a flight controller, a perfect match for the popular Omnibus F4 V2 Pro. ...Check it out at https://www.thingiverse.com/thing:2522611.

I also had no need for the bracket holes as I didn't plan on mounting this on any of my printers. So, I removed the side holes for mounting the case onto a bracket, I added small hexagon shaped vent holes to the top of the mode to better help with...

Which is ok, but when the S88 pro with it's even bigger battery came out, I went for it and so I needed a new case to mount it on the bike. This design works like the last one, there's a bottom and a top part that are held together by reusable cable...

Will update model when new board arrives here. Mounting holes for the screws are designed in a way that you can screw in a hot screw and it will thread itself. The buttons are part of the case. Both parts are hold together by the clips. Tolerances...

I threw this little case together for the LPC55S69-Espresso development board, specifically designed to print without supports and snap into place with its two halves. ...A hole is left at the top for the Mikrobus connector, which is positioned backward...

ATTENTION: this requires mirroring on the x axis. This is like the 20th version of this case for me. I am really happy with the fit. It should not require any scaling or adjustment. At least it doesn't on my ender 3 v2. The back of the case is just...

This is like the 20th version of this case for me. I am really happy with the fit. It should not require any scaling or adjustment. At least it doesn't on my ender 3 v2. The back of the case is just thick enough to protect the camera on flat...

Tripod camera mount for the Google 6 Pro with the Spigen Tough Armor case. This will not work without the Spigen Tough Armor case, or without a case, unless you make modifications to the mount. To make it work with a different case, or without a...

Case for NANO arduino board + MCP2515 module board. The pcb file will be added soon. ...

... E3 Case. ...He was gracious enough to make the STEP file available which made the editing rather easy. I removed the openings from the cover, as I didn't want filament to fall into the case, and shortened it to be in line with my existing drawer front.

... ...He was gracious enough to make the STEP file available which made the editing rather easy. I removed the openings from the cover, as I didn't want filament to fall into the case, and shortened it to be in line with my existing drawer front. ...

... space and provide more convenient access. ... This is a remix of the Minimalist Control Case from jckz82: https://www.thingiverse.com/thing:3127377 Replace the original cable with a longer 10-Pin (2x5) Female to Female 2.54mm-Pitch Flat Ribbon Cable

This is an application board for my Atmega32U4 PCIE based development board. It's got three stepper driver interfaces, a relay, and a 2 x 16 LCD parallel interface. The inputs comprise two buttons and an encoder. Everything needed to push the...