case for ipad 1st generation 3d models
2332947 3d models found related to case for ipad 1st generation.thingiverse
I'm trying to add a hole using remixer in the center of this case so that Wi-Fi reception the the iPad works well.
thingiverse
I made a re design of walters Arch ipad stand http://www.thingiverse.com/thing:189730/#made for the iPad 1st generation. 10/8/2018 added v2 of the stand. ...Stronger mechanical design at the front end to avoid cracking
thingiverse
Mount for iPad Air 1st Generation, designed to fit the IKEA HOVSTA 21x30cm (A4) photo frame. STL files for the whole frame are included, as well as a two-part split print for smaller print beds down to 220x160mm. ...To print in a the entire frame, a...
prusaprinters
I made a re design of walters Arch ipad stand http://www.thingiverse.com/thing:189730/#made for the iPad 1st generation. 10/8/2018 added v2 of the stand. ...Stronger mechanical design at the front end to avoid cracking</li> </ul> <h3>Print...
thingiverse
... cable of up to one meter in length, so that the USB plug can be plugged into a flush-mounted socket. Easy wall mounting with pluggable latch. The headphone jack is covered, but can be drilled out. Optimized for a RENKFORCE USB-A to Lightning cable.
thingiverse
Design a case inspired by Xbox ONE First generation. Slim PC for Microatx Motherboard, TFX format font, M2 SSD, Low-Profile Video Card. I provide all the STL files and also the SKP (Sketchup) for you to perform. (Portuguese) Projeto de um case...
thingiverse
A simple bracket to hold the iPad Air (1st gen) in place inside a iPad/iPad2 BookBook case from TwelveSouth (https://www.twelvesouth.com/product/bookbook-for-ipad) We upgraded from an original iPad to an Air, and these cases are expensive - so...
grabcad
Project #5! This is probably my best one so far because of the flat sides. Please download and like! ...Any comments are welcomed.
thingiverse
This is a minor tweak to Johncoffee's [1st gen iPad arch stand](https://www.thingiverse.com/thing:1874327). I tried to print it on its back but there is a slight curve which prevented the model from laying flat on the bad. This print corrects this...
thingiverse
Apple TV remote case for 1st gen Siri remote. ...I'm including the Blender project so you can customise it if you want to.
thingiverse
There's flexible place for tighing the screw and adapt it to each ducati monster 1st generation motorbike. ... I recommend you to print it with the most infill that you can if you want it be strong and resistful (mostly for the bottom where the screw...
prusaprinters
This is a 2-part Ipad case I designed to fit the 10.2-inch Ipad 7th generation device. I designed this in Fusion 360 and this is my first time using the program. The model is untested but was built using a scale model of the iPad. I intended to use a...
thingiverse
# 2021 iPad mini case (6th generation) The night I purchased my iPad mini my puppy jumped into my lap to see what was in my hand and the iPad almost slipped through my fingers. After looking at cases online ranging from $20 to $60 (why Apple?), I...
prusaprinters
2021 iPad mini case (6th generation) The night I purchased my iPad mini my puppy jumped into my lap to see what was in my hand and the iPad almost slipped through my fingers. After looking at cases online ranging from $20 to $60 (why Apple?), I...
thingiverse
... as a spacer. A bit of Vaseline on the tracks keeps everything sliding smoothly. The holder was designed specifically to fit the first generation iPad, but it may fit other models as well. ... See it in action at https://youtu.be/kmD4byosV4E
thingiverse
These were designed for a 2001 Toyota Tundra (1st generation) but I'm sure they'll fit many others or you can scale it as you like. Made with TinkerCad. **NOTE** the default print is a bit too tight. I recommend scaling these up by 1% which is...
cults3d
(1st Generation) The low bypass engine seems to refer to an engine having bypass ratio of 2 or less. Bypass ratio of this model is less than 1. This type of engine is ducted over the entire length of the engine, making it difficult to assemble. A. ①...
thingiverse
The firewire port was at the top at the time, and Apple hadn't created the dock for the iPod until the third generation of iPod with the introduction of the beloved (maligned) 30-pin connector. Similar dimensions to the iPod Universal Dock for iPod...
thingiverse
... rearwheel, frontwheel Add jetwall lenght 298 x100x100 Instructions print and paint......if you want! Further to remarks, I add new parts for light cycle in 3 pieces:body,rear wheel,front wheel
thingiverse
It's a ipad case with room for an apple pencil. It uses two magnets (from sonicare toothbrush currently) to hold the pen inside. The apple logo on the back removes so that the two pieces come apart. (use apple pencil charge port to lift logo) It also...
thingiverse
This is an STL file for an IPad Air 5 case. May be compatible with v4 and/or other versions. The idea is to print it using TPU or a mix of TPY and PETG. ...
prusaprinters
This adapter allows for using a 5 Generation iPad with a Bluetooth keyboard designed for an iPad 2. This adapter receives the iPad 5th Generation and mimics the shape of the edge of an iPad2 so that the iPad 2 can be placed in a Bluetooth keyboard....
thingiverse
I remixed this from https://www.thingiverse.com/thing:1206007 to allow it to fit an old 30-pin connector through it, and also allow it to hold an iPad+case with overall thickness of about 19.25mm. ...I made it longer and a little taller as well.
thingiverse
Mount for iPad Air 2nd Generation, designed to fit the IKEA HOVSTA 21x30cm (A4) photo frame. STL files for the whole frame are included, as well as a two-part split print for smaller print beds down to 220x160mm. ...To print in a the entire frame, a...