case for jetson nano 3d models

A simple Case for a Jetson Nano

Case for Jetson_Nano_2GB_DevKit_P3541

BOMPos.AmountName11Carrying case for NVIDIA Jetson Nano and Powerbank21NVIDIA Jetson Nano in a KKSB Compact Case for Jetson Nano31Aukey PB-N36 Powerbank4115mm polyester webbing 5215mm sliderAssembly instructions Place the Jetson Nano (Pos. 2) and...

This is a case designed to fit the IMX291-160 wide angle camera module for the NVIDIA Jetson Nano. It takes the Go Pro Hero 3 form factor for intended use with Tarot gimbals. Use countersunk M2 screws to mount the camera to the front of the case. ...The...

This is a case I created for the NVIDIA Jetson Nano 4GB + Geekworm T208 UPS Module. By purchasing this 3D model you're authorized to print as many as you want for yourself, you are not allowed to print for your friend(s), print to sell, or...

Jetson nano Case for B01 Assembly instruction video https://youtu.be/iDhCWCOdKTI Filament PLA: Black and Transparent PETG: Transparent green (used in the frame area where heat is applied) Print settings Support: none Infill: 20 percent What else do...

... first remix this one just shares the mounting hole portion. ... https://www.thingiverse.com/thing:1906831 Meant to work with modified case for a Jetson Nano Link to be added However thingiverses site has been crashing as I am publishing these files.

A Camera mount that slides into the slot of the Jetson Nano Case For the Jetson Nano Developer's Kit This is a mount for the IMX219-120 Camera for NVIDIA Jetson Nano which has the cable on the top side and lens in a different place than other mounts...

A Camera mount that slides into the slot of the [Jetson Nano Case](https://www.thingiverse.com/thing:3649612) For the [Jetson Nano Developer's Kit](https://developer.nvidia.com/embedded/jetson-nano-developer-kit) This is a mount for the [IMX219-120...

A very simple camera stand to be plugged on [ecoiras jetson nano case](https://www.thingiverse.com/thing:3603594). ... To fasten the camera to the stand you will need [M2x8mm fastener screws](https://www.amazon.com/dp/B00YBMRAH4/ref=cm_sw_su_dp) [Some...

This is a remix of the Jetson Nano Case by [ecoiras](https://www.thingiverse.com/thing:3518410) It is to get it to fit in with the [Raspberry Pi rack system](https://www.thingiverse.com/thing:3022136) and [DAP 2U rack...

These are the Case with I/O slot cover for the JetsonNano 1st/B01/2GB.It can be fitted with a fan.The SD card is not allowed to fall into the gap. JetsonNano Case for JetsonNano 1stJetsonNano_Case_Case_Top_A is Top Case with Top I/O...

Case for Jetson Nano 2GB version. Camera holder for RPI v2 camera Thread holes M3 to screw box together and mount camera arm, tighten just enough to move the camera. You will need smaller screws for mounting jetson board and camera. ...

You can also fit Nvidia Jetson Nano Dev KIT if you print the base (I didn't check for fitting so let me know if you have comments). After printing, thin films at holes for Power, USB, HDMI/DPORT and LAN needs to be removed. Sanding or cleaning may...

Remix of the Jetson Nano Case Connectors Edition top part by ecoiras to fit an arctic cooler fan with heatpipes. Print with 25 % Infill and PETG and probably a raft. PETG is highly recommended as PLA will become soft and melty when the jetson nano...

Case for Jetson Nano

Case for Jetson Nano. Case was made to replicate the Lenovo Legion T730. All dimensions were divided by 3.5 to make the mini scale. Part was designed for an acrylic sheet to be attached to the windowed side of the case. A second fan is able to be...

Full Snap together case for the Jetson Nano 2gb. Once its together it shuts pretty right. There are two side indents you can use to take the top off. ...

This is a case for the Jetson Nano Development board Revision B01. The wall thickness on these parts is way too thin. I'll have to thicken them up to make it a more viable housing. Hardware Vendors: 1. [McMaster-Carr](https://mcmaster.com) ...

# 3 Cases for your jetson nano rev. A02 #### I designed this so I could have a kali-like box on the go. #### Can manage small scale network security testing and penetration test. #### Designed to be slide in, no tool needed. Make sure you...

Jetson Nano case

jetson nano case

Jetson Nano case with VESA 100mm mounts. Modified/simplified to make it easier to print. ...Also relocated the antenna holes and made them permanent (and not knock-outs).

# Jetson Nano Case A minimal snap-fit case for the Nvidia Jetson Nano. The original design was very well done, but I prefer cooling over the logo. This is for the 4GB kit with all the ports, but I imagine also fits the 2GB kit. ## NanoBox...

Jetson Orin Nano case I made for myself, I haven't done printing the top part yet so I will update this after testing. Bottom part has 2 versions for one with PCI slot screw holes and the other is without them. ... Feel free to delete the mark...

GitHub link: https://github.com/dudasdavid/Jetson-nano-case Features: - Antenna mounting points for Intel 8265NGW Wireless-AC 8265 NGFF 802.11ac 867Mbps 2x2 MU-MIMO WIFI BT 4.2 Card - Lightpipe hole for status LED - 2 buttons for rerset and power -...

Nvidia Jetson Nano 2GB Case(Enclosure) with mounting holesCase has a snap in lip/groove design, no need to have additional fasteners. ...Will add camera ribbon feature in next model.

I drew up a basic case for the Nvidia Jetson Nano. It's designed to be small, lightweight, and durable. It's intended to prevent shorts and damage, not to completely cover the board, so you can throw your Nano in a backpack without damaging it. It's...

Jetson Nano CaseA minimal snap-fit case for the Nvidia Jetson Nano. The original design (<a href="https://www.thingiverse.com/thing:3603594">thing:3603594</a>) by <a href="https://www.prusaprinters.org/social/17411-ecoiras/prints">ecoiras</a> was...

NanoBox: a simple case for the Nvidia Jetson Nano. I left an opening for the heat sink at the top, which should permit attaching a fan using the screw holes already in place. There is also an opening at the back for easy access to the microSD card...