catalyst machineworks raging droner 3d models
2749 3d models found related to catalyst machineworks raging droner.thingiverse
Fin for the Catalyst Machineworks Raging Droner 6.0mm Fin to aid in turtle mode. Spacer used to center the front part of the fin. Use with my Antenna Block for a better rear fit. ... 20% infill with 3 wall layers
thingiverse
Integrated Capacitor holder for Catalyst Machineworks Raging Droner. ...One with holder for TBS Crossfire Antenna and one without.
thingiverse
This is an antenna block for the Catalyst Machineworks Raging Droner. Designed as a replacement for the stock antenna block as well as a version to fit my Fin design for the Raging droner. The 7.5mm version is the factory distance to fit Catalyst...
cults3d
It is a Re-design of the Rayenator "Catalyst Machineworks Arm Guard" https://www.thingiverse.com/thing:3688251 Add extra protection Now I can hit concrete without delaminating the arm. Original design was good but I need more protection. Add...
thingiverse
It is a Re-design of the Rayenator "Catalyst Machineworks Arm Guard" https://www.thingiverse.com/thing:3688251 Add extra protection Now I can hit concrete without delaminating the arm. Original design was good but I need more protection. Add...
thingiverse
Designed for the Catalyst Machineworks Raging Droner Used to prevent strain on the ESC-to-Battery pigtail in case of a battery ejection. Installed print is shown in the photos. ... Print with 20% infill with 3 wall layers
thingiverse
A simple Print . ... It allow you to install RaceLite LEDs or Racewire on the thin arms of the Raging Droner.
cults3d
A simple Print . ... It allow you to install RaceLite LEDs or Racewire on the thin arms of the Raging Droner.
thingiverse
I made it to be able to fly until I receive replacement part from Catalyst Machineworks. I print it with PETG. I still fly with it. ... It stills survive to many hard crash
cults3d
I made it to be able to fly until I receive replacement part from Catalyst Machineworks. I print it with PETG. I still fly with it. ... It stills survive to many hard crash
cults3d
It also base on the "Raging droner RD5 rear led sma" from "calefpv" https://www.thingiverse.com/thing:3688516 Over the original design I have add a Bumper to the front Profile, A RX compartment to the Back Profile and the Rear Profile support a...
thingiverse
It also base on the "Raging droner RD5 rear led sma" from "calefpv" https://www.thingiverse.com/thing:3688516 Over the original design I have add a Bumper to the front Profile, A RX compartment to the Back Profile and the Rear Profile support a...
thingiverse
Replaces the tpu part for the catalyst machineworks massive droner 3 inch hd. Mounts an immersionrc ghost qtee antenna and a vista antenna. ... full build: https://rotorbuilds.com/build/26782
thingiverse
I didn't like the stock mount with the Massive Droner HD and the angle it put the antenna at so I created this.
thingiverse
GoPro hero 6/7 mount for Raging Droner from 20 to 45 degree. No props in view. The earlier version has been upgraded to prevent jello. Use D40 TPU or something stiffer Print profilv5 with infil 20% or less. It does not matter Connector have to...
thingiverse
The original bumpers ordered from Catalyst Machineworks did not fit well, these ones do.
thingiverse
----- Arm guard for the Catalyst Machinworks Raging droner. Made to mount between the arm and the motor. I needed a spacer due to my motor screws touching the motor with the CM provided screws. Recommend using threadlocker on motor screws. ...
thingiverse
Canopy for Catalyst Machineworks Merica. Canopy is designed for: -Matek F722 -TBS Pro32 Nano (+Small Heatsink) -Frsky R9 Mini -Runcam Micro Swift 2 (or similar) -RealPIT switch -SMA bulkhead connector -AXII antenna (or similiar) Locate...
thingiverse
Mount for the Catalyst Machineworks Banggod frame that combines the air unit and antenna spire.
thingiverse
It's a realisation asked for catalyst machineworks. ...Soft mount for pigtail and matek GPS. Standoff height: 22 mm. Offset 27 mm. Diameter: 5 mm. To download : https://cults3d.com/en/3d-model/game/catalyst-machineworks-pigtail-gps-matek
thingiverse
Some parts to Catalyst Machineworks Slamnasty 3" racer: - Arm guards - Motor wire guards - Cam mount - Micro AXII mount
thingiverse
Catalyst Machineworks Merica Canope with extended Legs and more space for the Air unit. Hope this is usefull to someone. ...Have fun :)
thingiverse
Modular Parts for Catalyst Machineworks BangGod Talystmachine Frame BN-220 Mount TRUE RC Long Airunit Antenna Mount Front Bumper GP Mounts ViFly Mini
cults3d
It's a realisation asked for catalyst machineworks. Soft mount for pigtail and matek GPS. Standoff height: 22 mm. Offset 27 mm. ...Diameter: 5 mm.
thingiverse
This is a GoPro 7 mount for the Catalyst Machineworks Superlight. This is designed to mount directly on top of the top plate. ... Printed with TPU at 30% infill for best results.
thingiverse
This is a pod for the Catalyst Machineworks SL5 and SL6 (regular and norris edition). It is designed for the Runcam Micro Swift camera, but any micro camera should fit. ... Use self tapping screws to secure it to the frame (Phillips head #4 x 1/2” long...
thingiverse
Simple skid for the Catalyst Machineworks Shocker 5". I printed in ABS, but I'm sure you can get away with TPU or PLA just fine. ... This is a Remix from mjameskeogh's Tank deisgn @ https://www.thingiverse.com/thing:4702501
thingiverse
Simple and easy adapter to attach the Micro AXII antenna to Raging Droner frame. ...Simply push through the SMA hole and secure with 2,5mm zip tie.
thingiverse
Rear side for the Raging droner. Made the sma connector a tad higher so the connector wont hit the stack also added a led spot on the back, u can fit 2 addressable leds on that spot. print on its side. ... infil 60%