catalyst machineworks shocker 3d models
1406 3d models found related to catalyst machineworks shocker.thingiverse
Simple skid for the Catalyst Machineworks Shocker 5". I printed in ABS, but I'm sure you can get away with TPU or PLA just fine. ... This is a Remix from mjameskeogh's Tank deisgn @ https://www.thingiverse.com/thing:4702501
thingiverse
A 30 degree SMO 4K mount for the Catalyst Machineworks Shocker Ultralight frame. ...All ports and vents have cutouts and there is plenty of clearance for 5" props.
thingiverse
I designed this for the catalyst machineworks shocker 4 GPS Mount is designed for the BN-180 GPS Module. Comes with the reducer for the caddx vista antenna. ...
thingiverse
I designed this for the catalyst machineworks shocker 4 front mount. GPS Mount is designed for the BN-180 GPS Module. If your looking for a bigger mount for a different gps send me a message. ...
thingiverse
Front, Mid and Rear bottom skids for the Catalyst Machineworks Shocker Ultralight frame. I started designing these before CMW released their Shocker Tank skids, but ended up tweaking the design to match. Front and Mid skids are designed to...
thingiverse
Tested with: * Caddx Peanut * Catalyst Machineworks The Shocker (3.5") * Catalyst Machineworks Shocker Tank (5") You'll notice that you don't necessarily need the remix, as you can just use the two parts by themselves, by screwing one to the other,...
thingiverse
This is a Catalyst Machineworks Shocker - Naked GoPro (BetaFPV Case) and Insta360 GO mounts. The style matches the existing aesthetic of Catalyst's original included antenna prints. This requires two (2) 20mm standoffs to locate and attach the print...
thingiverse
couldn't find many insta360 one R 4k mounts at all, even less so for the catalyst machineworks shocker tank, so I grabbed [an existing one](https://www.thingiverse.com/thing:4605559), cut of the foot, and replaced it by some feet that mount to the...
thingiverse
This is a remix of https://www.thingiverse.com/thing:4113481, but the Thingiverse search tool won't let me add it I've made some new end guards that fit Shocker Tank and BangGod 5". The rear ones simply replace the existing 2mm piece that's slotted...
thingiverse
I’ve only printed this in PLA+ but convinced it will work just fine in TPU also. I’ve deliberately designed it to be a tight fit (no vibration). ... Hope it helps guys
thingiverse
This Insta360 SMO 4K mount is for a Catalyst Machineworks 4 inch Shocker ultralight drone. Im am not sure this will work for the 5-inch version. Print at your own risk. This is a minimal design with angle adjustability. There is also a retaining hole...
thingiverse
This base accepts my Hero 8, Naked 8 and Hero 9 cased, so they can be easily swapped between Shocker Tank, BangGod and Geyser. (could be easily adapted to just about any quad) https://www.thingiverse.com/thing:4623177 ...
thingiverse
did a quick model. ... 100% infill is about 7g
thingiverse
front buzzer mount for ..JHE20B Quad Finder with a minimalist landing skid rear gps mount for ...MATEK GPS MODULE SAM-M8Q that started with this antenna mount but needed a couple changes to fit the 4" and added a gps mount...
thingiverse
VTX antenna mount for Catalyst MachineWorks 5" Shocker Tank freestyle drone. ...
thingiverse
Designed this tail for the Catalyst Machineworks Shocker Tank HD 5in. ...It will hold the o3 air unit antenna along with an immortal T.
thingiverse
The original bumpers ordered from Catalyst Machineworks did not fit well, these ones do.
thingiverse
Canopy for Catalyst Machineworks Merica. Canopy is designed for: -Matek F722 -TBS Pro32 Nano (+Small Heatsink) -Frsky R9 Mini -Runcam Micro Swift 2 (or similar) -RealPIT switch -SMA bulkhead connector -AXII antenna (or similiar) Locate...
thingiverse
----- Arm guard for the Catalyst Machinworks Raging droner. Made to mount between the arm and the motor. I needed a spacer due to my motor screws touching the motor with the CM provided screws. Recommend using threadlocker on motor screws. ...
thingiverse
Mount for the Catalyst Machineworks Banggod frame that combines the air unit and antenna spire.
thingiverse
It's a realisation asked for catalyst machineworks. ...Soft mount for pigtail and matek GPS. Standoff height: 22 mm. Offset 27 mm. Diameter: 5 mm. To download : https://cults3d.com/en/3d-model/game/catalyst-machineworks-pigtail-gps-matek
thingiverse
Some parts to Catalyst Machineworks Slamnasty 3" racer: - Arm guards - Motor wire guards - Cam mount - Micro AXII mount
cults3d
It's a realisation asked for catalyst machineworks. Soft mount for pigtail and matek GPS. Standoff height: 22 mm. Offset 27 mm. ...Diameter: 5 mm.
thingiverse
Modular Parts for Catalyst Machineworks BangGod Talystmachine Frame BN-220 Mount TRUE RC Long Airunit Antenna Mount Front Bumper GP Mounts ViFly Mini
thingiverse
Catalyst Machineworks Merica Canope with extended Legs and more space for the Air unit. Hope this is usefull to someone. ...Have fun :)
thingiverse
This is a GoPro 7 mount for the Catalyst Machineworks Superlight. This is designed to mount directly on top of the top plate. ... Printed with TPU at 30% infill for best results.
thingiverse
This is a pod for the Catalyst Machineworks SL5 and SL6 (regular and norris edition). It is designed for the Runcam Micro Swift camera, but any micro camera should fit. ... Use self tapping screws to secure it to the frame (Phillips head #4 x 1/2” long...
thingiverse
Fin for the Catalyst Machineworks Raging Droner 6.0mm Fin to aid in turtle mode. Spacer used to center the front part of the fin. Use with my Antenna Block for a better rear fit. ... 20% infill with 3 wall layers
thingiverse
These are some parts to equip my Catalyst Machineworks Shocker UL 5in: - GPS_Mount: This part fits on top of the GPS mount provided by Catalyst Machineworks (I use the 'Optional Rear GPS Mount + Immortal T Mount'...