catan number tokens 3d models
120778 3d models found related to catan number tokens.thingiverse
These are the Catan number tokens as 3D pyramids. ...The advantage over the original tokens--other than being cool and 3d printed--is that they can be viewed right-side-up from any side.
thingiverse
Settlers of Catan number token broken into two smaller sets for printers with a smaller print surface. ...I tried printing the original on a Micromake D1 clone and had some issues at the extreme edges.
cults3d
Number tokens for Catan, adapted from rbschultz's number tiles (112018) with the numbers/dots extruded inward instead of outward.
thingiverse
Number tokens for Catan, adapted from rbschultz's number tiles (112018) with the numbers/dots extruded inward instead of outward.
prusaprinters
Number tokens for the base 3-4 player game and for the 5-6 player expansion game.Print pauses are recommended to change filament colors. The bottom and top layers are colored with the same filament used for the main hex tile rings. The inner layers...
thingiverse
I spend a few hours separating the tokens into separat groups, so that it's easier to print a single one (if a piece goes missing) or easier to print them in smaller batches on a smaller bed. Proviede is a Cura projekt file with everything in it....
thingiverse
All of the Settlers of Catan number tokens I could find were vector with only outlines for text. I wanted a solid text layer so that I could etch the text and cut the tokens. With painting the acrylic, I found that it was easiest to etch deep. If...
thingiverse
Really, Catan number tokens? Sure, I could have reused the cardboard ones from the original set with my custom 3D printed board, but where's the fun in that? This is a set of number tokens for the basic 4 player set. I've also created **[tokens for...
thingiverse
Really, Catan number tokens? Sure, I could have reused the cardboard ones from the original set with my custom 3D printed board, but where's the fun in that? This is a set of number tokens for the basic 4 player set. I've also created **[tokens for...
thingiverse
My version for the numbers tokens of Catan - https://www.catan.com The numbers are in the top, with probability dots. On the bottom you have the letters. ... These tokens are also good for Dakanzla set - https://www.thingiverse.com/thing:1238980, I...
thingiverse
Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709
thingiverse
As i have a friend that even knows wich character ends up in which number, i made a version, where you cant see the characters. ...
thingiverse
These are tubes designed to store my **[Catan Number Tokens - 4 Player Set](https://www.thingiverse.com/thing:2884108)** and **[Catan Number Tokens - 6 Player Set](https://www.thingiverse.com/thing:2884126)**, and are a remix of **[CNC...
thingiverse
A remix of tvputten's tokens designed for dualstrusion printers so you can get a nice crisp contrast between the disc and its number, without painting. I recommend a white bottom and either black or red tops to match Catan's discs. As with...
thingiverse
There are two different number token tube to hold your tokens. 3-4 player and they 5-6 players. I want a little bit of a more fancy holder with labeled lids. I used these number tokens. The threads should have been a little less fine, but the still...
thingiverse
My number tokens must be thicker as they did not fit in the organizer - I simply stretched the body in TinkerCAD, now it's perfect! ...(OK, perhaps 1mm too much room)
thingiverse
Yet another version of number tokens for Settlers of Catan. The set has enough tokens for the 6 player extension, but can also be used with the standard 4 player set. On the front of each token is the number, with pips and color, and scaled...
thingiverse
Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709
thingiverse
Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709
prusaprinters
Created a 3 part tube; 1 cap (with catan logo) 1 tube for 4 player chits and a 6 player tube (with a catan logo on the cap). The tubes are designed for tokens 25mm in diameter and 3 milimeter high. I used tokens with 2mm white discs and 1mm numbers...
thingiverse
I used tokens with 2mm white discs and 1mm numbers and dots. This design needs support. I used a x-y of 2 mm so the threads don't get support. This way you end up with a single tube with two compartments. After making this, I would recommend...
myminifactory
Credit where it's due: https://www.myminifactory.com/object/3d-print-catan-numbers-19344 I love Settler's of Catan. For me, like many others, it was the first step out of the world of Monopoly and Checkers into the world of mature and well-designed...
thingiverse
These are the number tokens with the letter on the backside as sorted in the original game. I also changed the size of the numbers according to the likeliness of occurance of the number - also as it is in the original game. In fact I took the scad...
thingiverse
This is remix of the number tokens from http://www.thingiverse.com/thing:1238980. I wanted to print them with dual extrusion to add the colors, instead of having to paint them. One set just contains the 6/8's for printing in one color. ...The other...
prusaprinters
This is remix of the number tokens from http://www.thingiverse.com/thing:1238980. I wanted to print them with dual extrusion to add the colors, instead of having to paint them. One set just contains the 6/8's for printing in one color. ...The other...
thingiverse
Just seperated all the parts in original and created an expansion set for multicolor printers.
thingiverse
I have created a 3D printable set of number tokens which fit a 3D printed board game or the original game. I have added dual print models for those who want to print dual colour. ... Check out my full 3D printed catan board set.