cateye bike computer 3d models
59021 3d models found related to cateye bike computer.myminifactory
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999).Screw is moved to front unlike the original.Designed in two hours, in third hour it was printed :-)Mounted, tested, is OK.As bonus I added reinforcing ring for my bike rearview...
cults3d
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999). Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. ...As bonus I added reinforcing ring for my bike rearview...
thingiverse
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999). Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. ... As bonus I added reinforcing ring for my bike...
prusaprinters
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999). Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. As bonus I added reinforcing ring for my bike rearview...
thingiverse
I have a couple of older Cateye wireless bike computers that didn't come with stem mounts. I saw a couple of models on this site that were close but wouldn't fit. mread's frame mount for the Strada seem the closest. The Strada's mount (and most...
thingiverse
Handlebar mount for Cateye Velo 8 CC-VL800 bike computer. Secures with M5 cap head screws. Designed for 22mm diameter handlebar. ... The two small holes in the mounting plate are for small brass "pins' that I will make to mate with the electrical...
thingiverse
Remix to add direct mount headset cap with Cateye Micro Wireless Bike Computer mount on top. Remix from mentalbob, good design just wanted to see if this works good too. ... Fits in stem replaces headset cap.
thingiverse
Since the installation of spurcycle bell on my brompton, i found the brompton bell redundant. ...Hence i created this bell mount to be able to hold my Cateye Wireless Computer.
thingiverse
A mount for attaching Cateye wireless bike computers (specifically the Cateye Padrone+) to Bontrager Blendr mounts. ...
pinshape
An easy and reliable mount places the bike computer in front of the take-out, contributing to better aerodynamics and better visibility on the screen, suitable for Garmin, Briton, Cateye bike computers, all the necessary mounts included, ABS, 4...
thingiverse
CATEYE bike computer mount stub for modding the LG Nexus 4 phone case by Zodd http://www.thingiverse.com/make:37263 into a bike mount. ... Instructions Printed in Makerware on High setting in ABS: 50%...
thingiverse
A bracket for mounting a CATEYE bicycle light. ... Zip ties can be used for fixing on a handlebar.
pinshape
I made it for HB100 dimensions but the internet says it also fits to other cateye computers like: MT300 ED200 AT100 VL200 VL100 + the harness includes a self locking magnet holder for the wheel, a sensor for the fork and also has got a quick release...
thingiverse
I made it for HB100 dimensions but the internet says it also fits to other cateye computers like: MT300 ED200 AT100 VL200 VL100 + the harness includes a self locking magnet holder for the wheel, a sensor for the fork and also has got a quick release...
thingiverse
This is a replacement screw for CATEYE bike lights like the GVOLT80.
prusaprinters
<p>I printed this model out of PLA with a 0.2 mm nozzle. ...A 0.4 mm might have done the job too.</p><p>The part fits great, it is very similar to the original. It might also fit other cateye products.
thingiverse
This is a mount for a Cateye Padrone bike computer. I wanted to take advantage of a barfly mount so i made this to integrate with some of the garmin barfly mounts here. I cut the garmin mount out and added the Padrone mount. The Padrone is odd in...
prusaprinters
A rear bike light mount specifically for the Cateye rear lights (specific models below) to mount horizontally under an Ergon QuickClick supported saddle. Ultralight and sturdy!</p><p><strong>Details</strong></p><ul><li><strong>Weight:...
cults3d
FOLLOW ME ON INSTAGRAM: PB023_3d Bike mount for the torch cateue volt. ... 2 models for diferent diameters_ 20-22 cm and 30-32 cm
thingiverse
Useful spare bracket for these bike lights. Strap it to your handlebars with a couple of thin cable tyes and put a piece of rubber(e.g. from an innertube) between the bracket and the handle bars to stop it slipping. You may need to file it a bit to...
thingiverse
This puts the computer out of the range of the wireless transmission, so I made a bracket to mount the computer onto the crossbar, closer to the sensor. The bracket allows the computer to swivel, so the button located on the back of the computer can...
thingiverse
Got a Lezyne bike light. ...Would like to mount on the Cateye bracket.
thingiverse
Bracket to attach a CatEye ViZ450 rear bike light to a Topeak Explorer MTX rack. Will probably work for other CatEye rear lights, as they appear to use the same mounting system. ... The light clicks into place on the bracket and holds well during rides,...
myminifactory
A replacement rear bike light holder for CatEye backlights. Printable without any support material and as a single part. It should fit for CatEye TL-LD xxx and TL-AU100. Designed for a pipe diameter of 27 mm with an angle of 15°. The Fusion 360...
thingiverse
Replacement part for a Sigma Bike Computer. ... I think it should fit for all basic Sigma bike computers.
thingiverse
A replacement rear bike light holder for CatEye backlights. Printable without any support material and as a single part. It should fit for CatEye TL-LD xxx and TL-AU100. Designed for a pipe diameter of 27 mm with an angle of 15°. ... The Fusion...
cults3d
A replacement rear bike light holder for CatEye backlights. Printable without any support material and as a single part. It should fit for CatEye TL-LD xxx and TL-AU100. Designed for a pipe diameter of 27 mm with an angle of 15°. ... The Fusion 360...
thingiverse
Shell for an arduino powered bike computer using a 128 x 64 oled screen