cc2530 router 3d models

The Baseplate is sized for a Porter-Cable model 450 compact/trim router, but I believe it can be modified for other routers. I included it here as an .STL, but it should be machined from acrylic I do hope someone may find this model useful. ...Please...

This 3D model set showcases a photorealistic Huawei B315 wireless router, including both versions with and without antenna. The dimensions for the router with antenna are L18.9 x W6.5 x H28.8 cm (L7.4 x W2.6 x H11.3 inches), while the model without...

The depicted model shows an off-the-shelf harbor freight 2-horsepower router, which is actually an incredibly potent and versatile tool; I possess every available size, ranging from 0.125 inches up to 0.5 inches. However, this massive machine suffers...

This jig bolts directly to the Makita RT0700 handheld router using its existing interface and a bolt on the side of the small base. No additional tools are required and no play exists. Using a small metal pin or drill bit as a center point, you can...

My First Attempt at Creating a Z-Axis for My DIY Router. Based on the Type 775 DC Motor, I've Designed a Linear Drive with a NEMA-17 Stepper, an 8mm Lead Screw, 8mm Steel Rods and Bearing Blocks. I Wanted to Make It Flexible in Z-Offset, So I Added...

I made this to mount my router by hanging it from an existing picture hook. I printed it upright with a brim and supports in PLA. ...If you're going to print this, make sure you have tuned your printer very well for dimensional accuracy, as there is...

I have a Woodhaven router planing sled and 3010 rail kit for planing large boards, epoxy resin castings, etc. I thought that it needed a little device to hold it squarely against the fence on one side. After some measurements and quick design work in...

A compact vise is designed specifically for use with the 4030 CNC router, capable of securely holding stock up to 40mm in width. This vise comes equipped with a clamp that can be screwed on top to firmly hold down the stop. To utilize this setup...

Small 240x125mm shelf for a router or modem that can be hung on a 19mm wide ledge.You'll need 4x M3 square nuts and 4x M3x8 or 4x M3x10 screws; grab them from the printer's spare bag if you still have it. Installation:Put the nuts into the...

Hi everyone, I recently got some great clips for my CNC router, but I faced a small issue when trying to attach them to a table. The problem was that the bottom platform only had four holes for screws, so I designed these mounts myself and thought it...

You print the ones you need, and carve out the area around the number with your router. I intend to paint the area that gets carved with a dark color so the wooden numbers stand out more. ... Anyway, a work in progress, but I'm happy with how it is...

Remix of TabLeft's centering cone design, to enlarge it for use in wide-bore base plates for larger router bits. ...Fits the shank that comes with the DeWalt centering cone, or 1/4".</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p>...

GENERAL The scene revolves around a single object: Router Tenda N301, with precise dimensions: Height - 18.5 cms or 7.3 inches; Width - 16.1 cms or 6.3 inches; Depth - 9.1 cms or 3.6 inches. Materials Used: This model was originally created using...

I designed a dust collector for my palm router since I couldn't find one on the market. Use this only when doing flush trimming work. The vacuum port is 28mm in diameter outside. I've included the body design so you can add your own vacuum port if...

I'm on the hunt for a router stand that'll hold my device upright with ease. The one I've got is a bit longer and thinner than the original, but it still sports the same general profile - a sleek design that's perfect for keeping things tidy. To get...

Stock guide for router or table saw.Consisting of 3 3D-printed parts and a few bits of hardware, this is a budget friendly system inspired by Jessems clear cut system.The wheel has grooves for two O-rings for better grip. ...(OD: 38, ID: 30)It is angled...

I designed this infeed guide to work with a router table I built using Jess-Em components.  It requires three 1 inch ¼-20 bolts, a 608 skate bearing, and a couple of o-rings that fit snugly on the outer ring of the bearing.  The nuts go in the knobs...

Lost or broke your router table insert? I did, and it was a huge relief when I replaced it with one that fits perfectly. This new insert is a much better match than the original one, and it's actually flush with the table, ensuring consistent results...

This is my ultimate router corner radius jig. The customizer lets you create jig versions for various types of curved or round corners: rounded outward, rounded inward, elliptical or chamfered corner routings. Open the unpacked .scad file in OpenSCAD...

You print the ones you need, and carve out the area around the number with your router. I intend to paint the area that gets carved with a dark color so the wooden numbers stand out more. ... Anyway, a work in progress, but I'm happy with how it is...

I already use a hooked device on my wire shelves for filament spools https://www.thingiverse.com/thing:2911934, so I took inspiration from that design and adapted it to match the back of the bracket I wanted for the little router. After some...

Modular router plate for the Bosch GKF-12V. Highly inspired and based on thing 3707881 by EpicFazer. I wanted a plate that I could use for different purposes, without having to disassemble the entire thing every time. It also has the added...

-This height gauge is perfect for router and table saw use. The template lets you make repeatable, strong, precise dovetail joints correctly with ease. By controlling the positioning of the teeth and the milling cutter, it is easy to accurately...

Holder for router ATTENTION: The part is not operationally safe and should therefore NOT be used in its original design under ANY circumstances. Experience: Pressure standing: - The top part tears off under horizontal load. => Remedy:...

New Model: Covid19 Face Shield Hole Punch V1.1 I created a version of this mask for use on a CNC router, utilizing 0.25" thick Polycarbonate and cutting with a 0.125" up-cut O-flute bit at 100 inches per minute and 22,000 RPM. I made three depth...

I recently got a finger joint router bit and decided that instead of constantly making tiny adjustments every time I needed to make the opposing side, it would be much more efficient to create a jig to elevate the work piece itself. This jig is...

I also wanted it oversized so I could hand hold it securely while using a handheld router. The uploaded version features a hole in the back to make this process even easier. It was actually the version in the picture that made me realize just how...

This is a set of mill hold downs I designed for my Genmitsu CNC router. This set includes various sizes and was designed to use M5 hardware. I purchased the following screws for this set: the 10mm - 14mm screws aren't needed, but I bought M5 screws...

This part is a custom replacement part designed specifically for a vintage Stanley 82901 router base that had been worn down by years of harsh use, finally cracking under the strain. The decision to include an adjustment screw made from sacrificial...

http://jasongriffey.net/librarybox/ There was a hooked device that I loved already for using on my wire shelves for holding filament spools, https://www.thingiverse.com/thing:2911934 So I thought I would take a little bit of the design and match it...