cc2531 3d models

Humanized with cutting-edge 3D modeling technology - 3D Slash!

Same as the original model, but instead of the big logo-hole, it has neat ventilation stripes.

The original case was perfect and it fitted my 2 Router Sticks perfectly. But, because one of the sticks is in my viewing angle if I sit down in the office and the red LED was to bright I decided to modify and add one 0.20mm layer over the logo. ...

Exactly like the original model, but I've repaired it and split into 2 parts (otherwise slicer splitting could fail, etc…)

<p>This dongle is based on the previous designs for the dongle. I have made some cosmetic changes to the corners and rounded the edges. Also I have included a mounting bracket so I can mount the dongle independently from my Raspberry pi. You can...

<p>Exactly like the original model (<a href="https://www.thingiverse.com/thing:2803664">https://www.thingiverse.com/thing:2803664</a>), but I've repaired it and split into 2 parts (otherwise slicer splitting could fail, etc…)</p>

Print this Model without any supports and with a layer height of .2 mm and 90% infill.You may need to heat up the cap after printing to make it conform better around the USB-A connector so it won't fall off.To close up the enclosure use superglue or...

... an internal SSD drive using a SATA to USB adapter. ...There's also a slot designed for a Zigbee CC2531 key.8 X (8mm / 0.8 mm) magnetsPrinted on an Ender 3 with PLA at 0.4mm.DIY : https://www.nlion.fr/installation-de-home-assistant-sur-un-raspberry-pi/

Tested with PLA 200°C Both sides should click together and hold by friction without gluing. Some light sanding will be required for the rouded edges. Disclaimer: Not tested for safety of the electronics. This includes but is not limited to: thermal,...

Tested with PLA 200°C Both sides should click together and hold by friction without gluing. Some light sanding will be required for the rouded edges. Disclaimer: Not tested for safety of the electronics. This includes but is not limited to:...

This is a box with snap lid for the RPI-ECU, designed to read the production of solar enrgy from Apsystems inverters yc600, qs1 and ds3. ...See also https://github.com/patience4711/RPI-APS-inverters Includes the STEP file for Onshape.Printed in PLA,...

CC2531 USB Stick Case for Zigbee2MQTT with Integrated Antenna Option

Visit my blog post about the Zigbee to MQTT conversion for more details on the case's design and the underlying hardware specs, located at https://jwillmer.de/blog/tools/raspberry-pi-zero-cc2531-case.

Case for Raspberry Pi Zero and a Conbee II Stick (or every other zigbee stick with equal size, I tried also with a CC2531). It's compatible with Raspberry Pi Zero and Zero 2, with or without GPIO Header. It also has enough space to almost any usb...

Please visit my blog post about the Zigbee to MQTT case for additional information about the case design and the hardware specifications. Print instructionsCategory: Electronics Summary Please visit my blog post about the Zigbee to MQTT case for...

About the case: This is a new and very compact case for my Zigbee to MQTT gateway It is locked via a 15mm M3 screw It can be mounted to a wall It has ventilation holes Size: 19 65 100 mm Additions: My old design is called Round Raspberry Pi Zero...

There is an USB panel connector where you can plug a Zigbee Key CC2531 or Combee https://www.amazon.fr/firmware-OpenHAB-ioBroker-zigbee2mqtt-antenne/dp/B08HVNF7WT https://www.amazon.fr/Dresden-ConBee-Electronique-II/dp/B07PZ7ZHG5 SoftWare: I use...

Don't short something out!\r\n5) Take the printed parts, put them in your device.\r\n6) You're finished\r\n\r\n### Printing:\r\nIMPORTANT case_p1.stl: rotate 60° y-axis, use brim and support IMPORTANT\r\ncase_p2.stl: rotate 180° y-axis, no brim, no...