cd display holder 3d models

This creation is built using Tinkercad. ...Make changes to it directly online at https://www.tinkercad.com/things/7bTBRQNVE8y.

It connects at the base for my weird car, thought others might want it, it a bash of two

2 version.

need m5 screws and nuts and rubber

Keychain holder Holders: no Filling: 10% @3D.todo.uy

Mount your Arduino to program and display vibrant RGB LED rings using these versatile bracket bases. The brackets fit snugly in place, remaining securely attached without the need for glue, although you can choose to add an extra layer of adhesion...

This was crafted specifically for an Adafruit 0.56" 4-Digit 14-Segment Display with I2C Backpack.

Minimalist CD Stand to display the case and cover art

LED lampshade that can also display CD booklets

This was designed for an Adafruit 0.56" 4-Digit 14-Segment Display w/I2C Backpack. Print instructionsCategory: 3D Printing

This design caters specifically to three 0.56" seven segment LED displays paired with Adafruit's HT16K33 backpack and associated display modules. Scaled for optimal use with an 8020 series 10 extrusion, this design offers versatility by accommodating...

This design is for three of Adafruit's 0.56" seven segment led HT16K33 backpack and associated display.The design is sized for use with an 8020 series 10 extrusion or equivalent. There are lots of led colors to chose from depending on use. The design...

Display holder for 5" display (BIGTREETECH PI TFT50) for Anycubic i3 Mega (S) ==================== This display holder can be printed in PLA / PLA+ / PETG / ABA etc. ... It was printed with the following settings: Layer height: 0.20mm Infill: 15 - 20%...

I swapped out the CD mount area for a tablet holder. ...Simply print this modified piece and replace the old holder with a standard car tablet holder that fits your vehicle perfectly.

Display holder for 5" display (BIGTREETECH PI TFT50) for Anycubic i3 Mega (S) This display holder can be printed in PLA / PLA+ / PETG / ABA etc. ... It was printed with the following settings: - Layer height: 0.20mm - Infill: 15 - 20% - Support: nN -...

 Display holder for 5" display (BIGTREETECH PI TFT50) for Anycubic i3 Mega (S) ==================== Updated version -------------------- Step file is also included in case you want to...

Držák se pouze nasadí na display a není potřeba nic lepit či šroubovat. U tohoto držáku je počítáno s tím, že je již použit zadní kryt displaye:For this holder, it is assumed that the back cover of the display is already...

Kiox Bosch Display Halter / Kiox Bosch Display Holder Ich habe die Kiox Aufnahme entwickelt mit Magnet Halterung. Man kann sie verschrauben oder auch mit Magnete hin hängen. Es werden Magnete benötigt von einer Höhe von 1,6mm und einem Durchmesser...

Racks V1 + V2 to store small displays, especially those with 3cm rings on each side and 5mm high, including the one I made: Attention it is only the rack for: https://cults3d.com/en/3d-model/jewelry/ring-holder-presentoir-a-bague The file B -...

gedruckt werden.Es wurde mit folgenden Einstellungen gedruckt:Layerhöhe: 0,20mmInfill: 15 - 20%Support: nNDruckplattenhaftungstyp: keine / Brim / Skirt Teile Information:Display-Backplate.stlInfill: 20%Support: nNGröße: 137.00mm x 92.00mm x...

<p>No Supports required</p>

infill: %20 Support: NO Material: PLA

I created this custom design to house an LCD temperature gauge within my water-cooled PC system.

Headphone Mount (20mm hanger) for smaller office headsets. Install with double sided adhesive tape. ...

Print a picture for my baby!

I had a pressing requirement to showcase some project documents, prompting me to create this curved design. ...To my delight, it functioned flawlessly on the first try, exceeding my initial expectations and providing an ideal solution for presenting my...