cd rom in macbook pro 3d models
1760846 3d models found related to cd rom in macbook pro.thingiverse
This is the starting point for a mini 3D printer or CNC machine using the stepper motors from a CD-Rom or DVD-Rom drive.
thingiverse
... speed in both directions. The base has a custom PCB that contains an Arduino Mini, ULN2004 transistor array and 5V regulator. (Eagle files and Arduino sketch included). I also superglued a CD-ROM to the top after spray painting the CD black.
myminifactory
I also modified it so that the motor from an old CD-Rom drive can run the pump. These motors are all about the same size, and anyone who likes to take things apart more then likely has a few laying around. In the photos I am powering a 6 volt motor...
thingiverse
I also modified it so that the motor from an old CD-Rom drive can run the pump. These motors are all about the same size, and anyone who likes to take things apart more then likely has a few laying around. In the photos I am powering a 6 volt motor...
thingiverse
Replacement for MacBook Pro laptop feet. Snaps into the holes, so NO need to open the case and use glues or plastic welding. ...Print/Slice at at least 0.1mm layer hight for the top pole so that the snap-in ring is formed properly.
thingiverse
A wall mounted Macbook Pro mount that slots into a USB-C hub. ... Designed to support this particular hub: Satechi Type-C Dual Multimedia Adapter with Dual 4K HDMI https://www.amazon.com/Satechi-Multimedia-Adapter-Gigabit-Ethernet/dp/B07RH8L9GV/
thingiverse
CD ROM Brushless Motor Ventilation. 3D printed motor propeller and 90mm Plica Pipe mount. 3mm motor shaft / 3mm CD ROM flange. 2X M3 screw and nuts. Can be used as exhausting fan or toy propeller. ... Up to 10000 rpm.
thingiverse
This is a derivative of Skimbal's CD-Rom motor pump, thingiverse.com/thing:4881, but with screw mounting and a 6mm circular outlet. Youtube video of it here: http://youtu.be/us2KlyBPEaU I may design a V2 sometime, possibly without screws and...
thingiverse
Using the shafts and steppers out of 2 CD/DVD ROM's. Now using it for scribing on copper clad too! Its not for the faint of hart and will take a little tweaking to set the current and voltage to run it proper. The motors can get slightly hot...
cults3d
You need to get the two centering teeth and glue them to the door (or screw them in), or reuse the original carriage. Place the rods in the slots and place the carriage. Grease the rods, carriage, and threaded pin. ... Use the two old switches on the...
thingiverse
so you have to change the ports in grbl-master\cpu_map\cpu_map_atmega328p.h in this file you have to switch ports from DIRECTION and PULSE of each axis ALSO spindle on/off with PWM is accesible over Z+ Endstop cause of switching the PWM port in GRBL...
thingiverse
All your Macbook plugs in one. ...Sit down at your desk and plug everything in at once: power, minidisplay, USB, and audio.
cgtrader
I exported to model without performing subdivision surface.To support low-poly , you can get high quality one opening subdivision surface.I created model in pieces and real sizes that you can create animations. It's a high quality model work,...
youmagine
Data Doubler to replace your DVD CD Rom drive in your Macbook with a second hard drive.Best printed in ABS or Nylon. I have not tested with PLA. Infill 20 - 25%.Will require a Slimline 13 pin SATA Male to 22 Pin SATA Female Adapter from...
thingiverse
i modeficated this lens adapter (from Andrew Barton : http://www.thingiverse.com/thing:19936) to fit a old cd-rom or dvd-rom drive laser lens.into it. for that cheap setup, it works well! if you whant to print this, you need to print the first...
thingiverse
This is a drop in replacement CD-ROM tray cover for 3DO Panasonic FZ-1 consoles. ...Also included is a version with the USB cutout for MNEMO's USB Mod I'm selling this on my website for those without a 3D printer:...
thingiverse
Adjustable power supply from old CD-ROM or DVD-ROM metal case. Two panels must be installed at both ends of the case. ...The dimensions need to be adjusted to fit your CD-ROM.
thingiverse
Middle gear for PC Engine CD-Rom Recommended SLA/Resin printer due to fine detail
thingiverse
These are the CD-ROM rails for an old case: Thermaltake Xaser III I got one of these cases, since now old hardware is very collectable and it was missing the rails for the CD-Rom bays. After many measurements and printing and testing i was able to...
grabcad
The Apple Macbook Pro is accessible in various screen sizes, and furthermore has an easy to use and thin plan. There are two expansive groups of PCs that must be picked these days. MacBook Air M1 and MacBook Professional M1 were dispatched last year...
thingiverse
This is a bezel and mounts for attaching a CD-Rom in the front of a desk made of 3/4" wood. ... These parts were used on my custom built computer desk seen here http://imgur.com/a/d5D1j after sharing my project on Reddit 3D Printing I received a few...
myminifactory
This is a bezel and mounts for attaching a CD-Rom in the front of a desk made of 3/4" wood. ... These parts were used on my custom built computer desk seen here http://imgur.com/a/d5D1j after sharing my project on Reddit 3D Printing I received a few...
thingiverse
this is a simple cover fo ATX computer CD-rom BAY . ...the solidworks file is supplied for any remix you want ;) free to use , free to modify :)
thingiverse
... Print 2 parts and glue them together. Others project "Box from CD-ROM housing": http://www.thingiverse.com/thing:1995138 https://www.thingiverse.com/thing:2149127 https://www.thingiverse.com/thing:4537745 https://www.thingiverse.com/thing:1965947
thingiverse
Use an old CD/DVD-ROM motor to make a 5-9V fan for well cooling stuff. 5V long life 9V well not sure... Press impeller on to motor shaft don't bend the shaft! Install motor and impeller assy into the housing and glue in place. Cover can be...