celestron camera mount 3d models
417297 3d models found related to celestron camera mount.thingiverse
To fix a camera on a Celestron AVX mount. !!! ...Be careful: Kodak bolt in PLA is very fragile for heavy camera !!!
thingiverse
Astrophotography camera adaptor for Celestron CG-5 equitorial goto mount Instructions Print with ~70% infill. A 1/4-20x5/8" hex head bolt goes through hole in bottom. (The part builds bottom-side-up.) Add one or two washers to fit the camera without...
thingiverse
Sometimes can be usefull to use the computerized movement of cpc800 for compensate sideral movements to take a long exposure photo using wide angle normal optics of cameras So i create this simple hook to mount a camera on it. Dimensions is inspired...
thingiverse
Me neither, so I made this adapter that bolts to the camera instead of the stock C-mount and replaces the part in the FirstScope focus mechanism that has the set screws to retain the eyepieces. Result is that the camera screws directly into the focus...
thingiverse
RPCCS : Raspberry Pi Camera Celestron Support Project version : V3 This project is to use pi camera on Telescope. This project is design to be print with plastic and/or metal (bearing,nuts, ....). It was also design to be modulable. The Pi camera...
cults3d
RPCCS : Raspberry Pi Camera Celestron Support Project version : V3 This project is to use pi camera on Telescope. This project is design to be print with plastic and/or metal (bearing,nuts, ....). It was also design to be modulable. The Pi camera...
thingiverse
Quick dirty picatinny style mount for celestron 127EQ telescope. I wanted to put a red dot on in place of the normal finder scope. This may need some modification for other telescopes. ...There are much better options out there, this was just something...
thingiverse
This mount moves the Motor drive out of the way so it doesn't cause interference. There was no reason for the original mount to be so poorly designed. It took me 1/2 hour to design and now it's perfect. Uses original hardware too. Built for an easy...
thingiverse
I have a Celestron Spotting telescope, and a nice tripod, but it only has one anchor point, so the telescope has a bit of twist and wobble. I designed this adapter so I get a more stable mount. Be sure to print it upright, because you don't want...
thingiverse
Celestron CGX is a great mount, I love it. But there a few tiny details, which can be annoying over time. For instance, only 2 two AUX ports are not enough for many Celestron accessories (Hand Controller, WIFI Skyportal, StartSense, GPS Module...).
thingiverse
It is designed for the 20 mm eyepiece from Celestron, the body of the eyepiece has an angled mounting section. I printed this eyepiece side down, telescope side up with supports. ( EGADS! I just saw a typo on the part as I uploaded the...
thingiverse
This is for a small Celestron telescope. Printed in PLA+ 100% infill and it feels very strong. But I am printing it again in ABS as this should be more robust. ...
pinshape
... When installing the mounting plate, please only remove two of the three screws of the focuser and replace them with the M3x10 screws. Adjust the screws until the focus tube turns smoothly. ...Then attach the motor and finally the gears.
thingiverse
With this mount you can use your smartphone camera to take pictures through your telescope. It can probably be used on different telescopes. IMPORTANT This mount is designed for a Sony Xperia XZ1 Compact only! ... NEEDED PARTS 3x M3 Screws 3x...
thingiverse
This is a webcam mount for the Celestron 600x microscope: https://www.ebay.ca/itm/256046138497 The camera mount is for this cheap Chinese webcam linked here: https://www.ebay.com/itm/224665919669 Was looking to do some time-lapse on samples I had...
thingiverse
I bought a Celestron StarSense but neither of the included mounts would work for my application. The default mount has a curved base to fit larger OTAs and I already have an autoguider popluated in the dovetail acc shoe. I have an 80mm refractor...
thingiverse
A nice wall-mount for the Celestron telescope. Securely holds it to the wall and out of the way! ...The spacer is used on the bottom below the primary mount to keep the telescope from putting too much strain on the mount.
thingiverse
This is a bracket for the Celestron Starsense camera. With this you will be able to use your Starsense camera on a second scope. No holes, but attach it to a flat bracket on your scope. ...This is solid plastic and will take about 7 hours to print out.
thingiverse
This is a dovetail mount for Celestron C8's. It might fit other 8" SCT's from Celestron as well, but I have no way of checking. The mount follows the curve of the scope so other sizes of SCT's like the 9.25 or 11 probably won't fit since the...
thingiverse
Fit standard Olympic counter weights to a DX equatorial mount and adapt Vixen rings to Celestron Dovetail mount. Use long brass thread in the white clamps with wingnuts. Glue a small piece of hosepipe inside the clamp with PVC glue. To move the...
thingiverse
... Also including Meade 390 mount for attaching Starsense dock to. Heat threaded inserts were used to allow the dock to be screwed to the mount. This mount would have to be custom made depending on your telescope or desired mounting preferences.
thingiverse
This is a Telrad mount designed to fit on the Celestron CPC1100 stock finder scope mounting plate. This allows swapping the finder scope for a Telrad without sticking that double sticky mounting plate all over your nice telescope. This will probably...
thingiverse
Filtro solar para el telecopio celestron 925, necesaria un filtro solar de al menos 20x20cm Remixed from ur7x
thingiverse
... add the Spacer over the screw with glue. 2. Insert the nut in the Mount, secure it in place with glue. Please note that Mount should be placed with the nut on the left when using the telescope, to be able to use the full range of motion (0°-90°)
thingiverse
Accidentally broke the red dot finder on my celestron telescope and decided to print out a new one since gluing didn't work so well.
thingiverse
I am using a Celestron Nexstar 6SE scope with the Hyperstar Mirror attached from Starizona, and connected to the Hyperstar is a ZWO ASI294MC PRO. I wanted the ability to cover the lens when I was done for the night without having to disconnect the...
prusaprinters
This is an accessory mount for a Celestron C8 telescope that provides a standard 1/4 20 screw to attach a spotting scope. ...I designed it to mount my 3D printed 80mm f/4 refractor to my C8 telescope. It requires: one tripod screw - to attach...
thingiverse
This is an adapter to allow mounting a laser sight to a Celestron Nexstar 6SE telescope. When using a GoTo scope, you need to find the alignment stars during setup. In my initial use, I'm still uncertain about the utility of this as a finder. The...
thingiverse
I needed an extra weight for my CGEM Mount and I had some curling weights laying around so I made this bushing to snugly fit into the weight and keep it snugly on the CGEM shaft.
cults3d
I needed an extra weight for my CGEM Mount and I had some curling weights laying around so I made this bushing to snugly fit into the weight and keep it snugly on the CGEM shaft.