celestron edge hd 8 3d models
420007 3d models found related to celestron edge hd 8.thingiverse
Dew protection cap for Celestron Edge HD 8" telescope. ...Precisely fits the OTA cap locking mechanism.
thingiverse
Fan's platform for Celestron Edge 8 HD. Install 2.5 x 5.5 plug with connected fan into the cover. ...Unscrew grid's bolts and install this platform.
thingiverse
I liked the design of the original (seen here https://www.thingiverse.com/thing:4573682) but it didn't fit the Edge HD 8, so I made a version that did.I also added a larger triangle support which seems to help a little.
thingiverse
Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
Custom Cover for Celestron Edge 8 HD and Glass Solar filter.
prusaprinters
ZWO EAF Holder for Celestron Edge HD 9.25 or other simillar Celestron SC telescope. Quick unlock for manual focusing. BOM 1x GT2 Timing pulley 20Teeth/Bore 5mm 1x GT2-142mm Timing Belt size 6mm 3x M4 worm 3x M3 x 15mm Inbus screw 2x M4 x 35mm Hex...
thingiverse
Bahtinov mask for Celestron 8" HD Edge with Hyperstar V4. Closes like a dust cap. The design with a loop and a latch to more easily put on and off the halves of the mask without having to remove Hyperstar with camera. ...Can be used with or without...
thingiverse
PLEASE DO NOT TIP FOR THIS REMIX This is a Bahtinov focusing mask for the Celestron NexStar Evolution 8" Telescope with Edge HD Optics. It is built from the excellent SCAD model generated by Aaron Griffith called "Telescope Bahtinov Mask...
thingiverse
ZWO EAF Holder for Celestron Edge HD 8, 9.25 and RASA 8 or other simillar Celestron SC telescope. ... You must cut the end of the handle cap to insert the drive shaft Design by Victor Sabet and Alain Poyvre
thingiverse
Lens Cover for a Celestron Edge HD 8 with Hyperstar 4. Needed a cover that would work with the hyperstar installed. It is split in half so it can be put on without disconnecting cables. A revision is planned to add a small section to cover the...
thingiverse
Fan for Celestron Edge HD 9.25" ### BOM * 1x 40mm 12V fan * 1x DC-025M 5.5x2.1 Power Supply Plug Connector * 1x KCD1-11-2P power switch * 1x 3mm Red LED * 1x 33K axial resistor 0.125W * 4x M3 20mm imbus screws * 4x M3 nuts * 4x 2x6mm self-tapping...
thingiverse
This is a counterweight mount for Celestron Edge telescopes (and all other models using the same dovetail). It allows for a counterweight (in my case Skywatcher 1.8kg counterweight) to be attached to the rail and balance your scope. Printed with...
thingiverse
Dew shield holder for Celestron 9.25" Edge HD ###BOM * 16x M3x10mm screw * 16x 2.5x5mm self-tapping screw ###Optional * W&W Astro dew heater 100 cm strap * Camping foam mat for create extension tube ###NOTE Use a tap to create a M3 thread
thingiverse
Solar filter holder for Celestron 9.25" Edge HD ###BOM * 4x 2.5x8mm self-tapping screw * 16x M3x10mm screw * 1x Solar Sun Filter Telescope Sheet [Black Polymer...
prusaprinters
Dew shield holder for Celestron 9.25" Edge HD BOM 16x M3x10mm screw 16x 2.5x5mm self-tapping screw Optional W&W Astro dew heater 100 cm strap Camping foam mat for create extension tube NOTE Use a tap to create a M3 thread Category: Other
thingiverse
ZWO EAF Holder for Celestron Edge HD 9.25 or other simillar Celestron SC telescope. Quick unlock for manual focusing. ###BOM * 1x GT2 Timing pulley 20Teeth/Bore 5mm * 1x GT2-142mm Timing Belt size 6mm * 3x M4 worm * 3x M3 x 15mm Inbus...
thingiverse
Bathinov mask for Celestron 9.25" Edge HD with Optec Lepus 0,62x reducer ###BOM * 7x M3x10mm screw * 7x M3 nuts * 1x M1.4x6mm screw * 1x M1.4 nuts
thingiverse
Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391 Instructions Using the following options:...
cults3d
Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
A duncan mask for a C11 edge. Useful for collimation and focus. ...
thingiverse
Tri-Bahtinov mask for focusing and collimation. ...Fits standard Celestron C8 and Celestron Edge HD8.
thingiverse
C11 Edge Tri-Bhatinov Masked. Generated via AstroFarmer's generated. Created in Tinkercad. ...
thingiverse
This is an exterior exhaust fan for a Celestron EdgeHD 8 telescope. It replaces one of the two vents on the rear housing. I suggest replacing the upper vent. The power cord required is the same type used by most GoTo computerized mounts. ...
thingiverse
I have a Celestron EdgeHD 8" scope with Hyperstar and ZWO ASI294 that I use for astrophotography/EAA. The cables to communicate with and power the camera must run in front of the corrector plate which can cause spikes in the images. I came across...
cults3d
... improve on it or simply change the hinge (it's a 1.5mm hole now, so might need to change), feel free. If I got it correct, it should fit my Celestron Nexstar Evolution 8. Update: It really works well. ... Read about Bahtinov_mask at the wiki page.
thingiverse
... hole now, so might need to change), feel free. If I got it correct, it should fit my Celestron Nexstar Evolution 8. Update: It really works well. ... Read about [Bahtinov_mask](https://en.wikipedia.org/wiki/Bahtinov_mask) at the wiki page.
thingiverse
I designed a dust cover for my RASA 8 that allows me to keep the camera mounted on the telescope. I use ZWO ASI183MC Pro with filter drawer from Starizona. Since my Prusa MK3 is not large enough to print it as a one piece, I had to split it into 4...