celestron nexstar models

Realistic 3d model of Telescope Celestron Nexstar 1025 LT

Inserts for Celestron Nexstar telescopes. Big Hole to Camera or Other Big Hole to "Button" type GPS Small Hole to Eyepieces with the caps on! ... A tray for the stock diagonal

A motorized focuser for a Celestron NexStar SLT90, with a SCAD file that may allow adjustments for other telescopes. It houses a 28BYJ-48 stepper motor. The motor mount contains a long curved bar which can fit securely in the gap between the scope...

I remodeled this from a real hand controller using SolidEdge since no useful drawings are available from Celestron. The Accuracy is within some mm (most dimensions < 1mm), Units are mm. ... Feel free to use it, let me know if you are also designing...

Ducan Mask to collimate Celestron Nexstar 6SE

Remote holder for Celestron Nexstar Evolution telescope mount, a more convenient place for me than the tripod leg.

Motorized focuser fos Celestron Nexstar 130SLT Telescope. ... For assembly it's necessary: 1x 25GA motor reduced to 5 rpm 4x bearings 623-2RS M3 screws and nuts.

Customized version of https://www.thingiverse.com/thing:160391 for Celestron Nexstar 8se Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391

This is a tripod adapter for a Celestron Nexstar altaz goto telescope mount that I picked up used for cheap. ... This requires just two pieces of hardware, just a quarter inch screw to connect to the mount, and a 3/4" t-nut to allow it to screw to a...

After the center piece of my Celestron NexStar 127SLT tripod cracked a few times I tried to look for a replacement piece. With no success, and after a few slight revisions, I came up with this bracket to help hold everything together. Hardware...

The Celestron NexStar 6SE and 8SE mounts are the same, except the gear cover/dovetail shroud. The 8SE shroud has a larger radius to accommodate the larger tube diameter. If you want to use a 6SE mount with an 8SE tube, you will need the larger...

A nice wall-mount for the Celestron telescope. Securely holds it to the wall and out of the way! ...The spacer is used on the bottom below the primary mount to keep the telescope from putting too much strain on the mount.

This brace was designed to address an issue with the SLT mount that comes with many Celestron telescopes. The original single sided fork looks beefy but is actually a bit thin and is only connected at 2 points to the turret. This causes a lot of flex...

Redesigned this to fit the Celestron NexStar 102 SLT

It follow the : Celestron Nexstar 6 SE myFocuserPro2 version 3This time sized for the Celestron Nexstar 8SE telescope.Measures from wei chen who needed this model.Compared to the 6SE , this model is reinforced at the back from the motor.It was done...

Bhatinov Filter for Celestron NexStar 6SE created using Bhatinov Mask Drawings Generator

Holder for Celestron Nexstar Hand Controller for C9 / C11 mounts ( or all 51 mm diameter tubes ). ... 40% infill 0.2 layer 4 perimeters

Holder for Celestron Nexstar Hand Controller for C9 / C11 mounts ( or all 51 mm diameter tubes ). ... 40% infill 0.2 layer 4 perimeters

Leg tightening bracket for Celestron NexStar tripod. Used pre-existing female nut insert from broken bracket and melted it into bracket using soldering iron. Used two half inch screws to secure bracket in place. ...Used ABS filament at 100% infill.

Leg tightening bracket for Celestron NexStar tripod. Used pre-existing female nut insert from broken bracket and melted it into bracket using soldering iron. Used two half inch screws to secure bracket in place. ...Used ABS filament at 100% infill.

Parts to cover gaps created by removing the metal part around the accessory tray on the Celestron Nexstar Evolution mount. ...It is useful to properly balance a 9.25 telescope without limitation in altitude.

It was specifically designed for the Nexstar 80GTL, but would likely work with other models. One set of parts converts the clamshell clamp to a Vixen dovetail clamp; the other converts the base to a Vixen dovetail so that it can be mounted on a...

Bracket to use the myFocuserPro2 on the Celestron Nexstar 6 SE telescope.3D Printed and tested , work perfectly.File format are 3dm native (Rhino 3D) , i added Step and Obj if needed.2018-05-13 : updated the bracket with long hole for telescope screw...

This is a printable Duncan Mask for a Celestron Nexstar SE8 telescope. it is printed in 4 pieces for my printer. the pieces are glued together to make the mask for use. When used aids collimnation process and allows adjustment of screws with less...

I have a Celestron NexStar 8SE telescope, so my beloved girlfriend design this thing for me, I post this thing here with her permission. Based on ( http://www.thingiverse.com/thing:321295 ) Update: It works really well. if your printer is...

I am using a Celestron Nexstar 6SE scope with the Hyperstar Mirror attached from Starizona, and connected to the Hyperstar is a ZWO ASI294MC PRO. I wanted the ability to cover the lens when I was done for the night without having to disconnect the...

Bracket that allows you to mount the Hand Controller on the Nexstar Evolution mount with facing to you.

So, I bought a second-hand Celestron NexStar 4E - it is in pretty good condition, but is missing the spreader which firms up the tripod legs - so i decided to make one. My 3D Printer has a build area of 100 mm x 100 mm, so it needed to be made in...

This is a replacement for the rubber feet that attach to the bottom of the NexStar SE mounts. They are not exactly the same as the original but they fit perfectly and look great. ...Should be glued in place but they stay on to an extent without glue...

This mask fits neatly inside a NexStar 6 Evolution and is easy to remove. Focusing works like a charm with an astro camera, takes out the guess work of lucky imaging. ... I've created the shape on this site: http://astrojargon.net/maskgen.aspx And...