celestron tripod parts 3d models
545871 3d models found related to celestron tripod parts.thingiverse
I bought a Celestron Astro Fi telescope and it was missing some parts. The tripod center disk was missing, so I designed one with 3 lens holder positions. The spreader arms are poorly made from factory, and the roll pins that hold them fall out....
thingiverse
Hopefully you make/made the upper part (https://www.thingiverse.com/thing:3935946) out of TPU. That makes it a very good dampener. I've found that the only downside to TPU without any support underneath is that it eventually bows down in the middle.
thingiverse
Clip to keep Celestron tripod legs togather, in various manners. ...
thingiverse
This is a part acessory for a Celestron Powerseeker 70az Telescope Tripod. I have printed it in 20% infill with supports. Print 3 supports for each base. ...
pinshape
this is an ABS replacement arm for the celestron telescope tripod spreader
thingiverse
Replacement arm for the tripod on the Celestron 130 Series of Telescopes - may fit other models.
thingiverse
... with something a bit more robust. Using heavy duty tripod feet was an obvious choice and these adapters should work well with any tripod foot with a standard 3/8-16 screw post. ... Should fit any telescope tripod with hollow 1" diameter metal legs.
thingiverse
This is a holder for the 38mm legs on a Celestron tripod. It basically snaps on and keeps them from opening up during transport. I printed in PETG for strength and heat resistance, but you could probably do in PLA as well. I would use a...
thingiverse
I have a Celestron Spotting telescope, and a nice tripod, but it only has one anchor point, so the telescope has a bit of twist and wobble. I designed this adapter so I get a more stable mount. Be sure to print it upright, because you don't...
thingiverse
I made this remix of LKLyon clamps as the originals were too narrow for the leg spreaders on my 102GT tripod. ...I beefed up the leg clamps and opened them up to fit my spreaders
thingiverse
This is a tripod adapter for a Celestron Nexstar altaz goto telescope mount that I picked up used for cheap. ... This requires just two pieces of hardware, just a quarter inch screw to connect to the mount, and a 3/4" t-nut to allow it to screw to a...
thingiverse
This adapter allows to use an Celestron Cometron or Firstscope with an old Vanguard VTP tripod. ... The support was based on this design https://www.thingiverse.com/thing:353135 and the tripod plate is based on mesurements taken from the original tripo...
thingiverse
This is a remix of a tripod adapter for a Celestron telescope originally made by adafruit. My tripod (a targus TGT-58TR) didn't work with the adapter plate in that, so I modified the adapter top from that project and just made it one piece since I...
thingiverse
After the center piece of my Celestron NexStar 127SLT tripod cracked a few times I tried to look for a replacement piece. With no success, and after a few slight revisions, I came up with this bracket to help hold everything together. Hardware...
thingiverse
replacement bracket for the leg for my Celestron PowerSeeker 114AZ. ...fit snug on mine could increase 1% to have a looser fit.
cults3d
replacement bracket for the leg for my Celestron PowerSeeker 114AZ. ...fit snug on mine could increase 1% to have a looser fit.
thingiverse
... by sirhc. ...I needed a bigger "box" clip for the tripod that would be able to fit my projected box that houses a Arduino mega + ramps board. Before I went to print I used netfabb stl repair and sliced with prusasclicer. ... Remixed with Tinkercad
thingiverse
Hello, This part is an Brace Arm for Celestron Astromaster 130 Tripod. ...I made this piece myself because mine broke.
thingiverse
These are replacement parts for a Celestron Powerseeker 50AZ. Since the original parts are very flimsy, it makes using the telescope very hard because these parts bend and spring back. These new parts are made beefier and when printed solid (all...
thingiverse
Fits a Celestron AVX tripod that has 2 inch diameter legs that are slanted 32.5 degrees from the vertical with accessory tray/spreader installed and tightened. 1/4" threaded insert on the shelf support is for securing the shelf. 6mm bolts in the...
thingiverse
Created a dovetail mount for a Star Adventurer to fit onto a Celestron Tripod.
thingiverse
my 3d printed bracket to hold the synscan unit on a standard Celestron eq3_2 tripod https://youtu.be/Vdawy2VJQGA
thingiverse
Parts List: - Tripod Head: available from Amazon or 3D print (https://www.thingiverse.com/thing:2475495) - Bolt: most Tripod heads take a 3/8-16 bolt - Large washer: place under the bolt head to spread the load Caution This design features a large...
thingiverse
Adapter of the Celestron Firstscope for the Rollei tripod. .f3d file included for any adjustments. ...Remember to rotate the object 90 degrees first before printing.
thingiverse
Leg tightening bracket for Celestron NexStar tripod. Used pre-existing female nut insert from broken bracket and melted it into bracket using soldering iron. Used two half inch screws to secure bracket in place. ...Used ABS filament at 100% infill.
thingiverse
This adapter allows to use a Celestron Firstscope with any Arca-Swiss Quick Release System tripods. ... Arca-Swiss Quick Release System: https://photographylife.com/arca-swiss-quick-release-system The support was based on this design...
thingiverse
These are customized "Smooth n' Curvy" knobs designed for mounting my Celestron 8" GPS telescope to its tripod. They use 3" long 3/8" bolts, leaving 1" protruding from the knob. Depending on your printers dimensional accuracy, you may have to ream...
prusaprinters
These are customized "Smooth n' Curvy" knobs designed for mounting my Celestron 8" GPS telescope to its tripod. They use 3" long 3/8" bolts, leaving 1" protruding from the knob. Depending on your printers dimensional accuracy, you may have to ream...