cell phone car holder vent 3d models
479600 3d models found related to cell phone car holder vent.thingiverse
UPDATE 7/29/2021 This is my take on one of those gravity cell phone holders that snap into a car vent. It should fit most phones ranging in width from about 3.75 inches down to 2.75. The phone holder frame attaches to the vehicle via a ball-nose...
thingiverse
This model is a parametric cell phone holder that mounts to the vents in your car. Every part of the design can be easily modified with the .scad file, but the only thing that should actually need to be modified is the length, width, and thickness of...
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
thingiverse
Customized version of https://www.thingiverse.com/thing:3014136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3014136
prusaprinters
Remix of Smart Phone holder for car vent by Walleye for easier printing. Allows for printing flat on print bed.</p><p>Prints in two parts, then superglue/adhere them together. ...I used supports for the overhands but not sure if that was...
thingiverse
This is a simple phone holder for the car. It hooks onto the vents. The vent hooks are attached to the back plate with 2mm wire (suspended ceiling wire from Home Depot.) The side hooks are work in progress. For now it is attached with zip ties. So...
cults3d
Assembly details can be found in the original work: https://cults3d.com/en/3d-model/gadget/cell-phone-desk-holder UPDATE: I add outside the .zip 5 mm bolt and nut for assembly. ... NOTE: I recommend the improved model by BEMORE:...
thingiverse
A simple phone holder for phones with a thickness of up to 10mm and a width of 55mm to 120mm.
thingiverse
This is a simple car phone holder suitable for iPhone 7 and Samsung A5 or other phones with similar width and thickness. Actually it could be easily adjusted by modifying the side support part. The original holder worked ok, but sat a bit too...
thingiverse
Made space for a charger, made sure the phone is more secure and doesn't fall forward at hard breaks. Added hooks for the rubber bands, so the pull completely horizontally. ...Also made the mount point smaller to fit the vents in my Saab 9-3.
cults3d
This is a support to use the cell phone as a GPS in cars that do not have it included. It is designed to be fastened in pockets, usually available in the central part of the board. This one is designed specifically for a VW Gol, but it is adjustable....
cults3d
It is a model that adapts to different cell phone sizes. No additional screws or tools are required to assemble it. The support for the ventilation grille is inspired by...
pinshape
Cell phone vent holder F150 for moto 4 1.0mm nozzle PLA, scale height 85.598mm.
thingiverse
Hook replacement for a generic rotating car air conditioner vent holder mount support for Samsung cell phones. It could be compatible for other identical supports used for different brands. You can check the pictures to be sure if hook would fit ok...
thingiverse
Universal phone holder that you can stick in your car vent. ...I used an old (broken) phone camera stand and cut off the legs at the bend, then designed this piece around it.
thingiverse
Magnetic car phone vent holder. Used 6mm x 2.75mm thick magnets. printed mostly in PTEG but with a TPU cover for grip. Recommend 100% infill for strength. ...other than that standered Cura setting, just changed the retraction down do 3.5 for TPU and...
thingiverse
Simple and robust phone holder. Sized for Huawei P10 Lite in rubber case. Ideal for Skoda / VW vents. ABS plastic, printed with raft and support. ... Model: https://www.tinkercad.com/things/fbpuWhCA1n1
cults3d
cell phone holder for air conditioner nozzle, model for samsung with labeled arm