cell phone charging dock 3d models

This product (ELECTRONICS ONLY) is a Mobile Cell Phone Battery Booster Charging Dock Station stripped back to just the functioning components, it has been specifically designed for hobbyist and 3D printer enthusiast. All you need to do is create...

cell phone dock

Cell Phone Charging Stand

Simple 5-Phone Charging Dock. It all fits!! ...No worries!!

Apple charging station for Apple Watch, AirPods (via cable) and Iphone 10 XS (via cable). ...All cell phones that do not exceed the width of the 10 XS are therefore also compatible. ...Changes / wishes gladly on request

Charging Dock

... sitting on the floor. This Cell Phone charging Shelf should fit for all (Samsung) chargers which look like the one pictured. Instructions Nothing special. ...Just rotate it bottom-up for printing.

Phone stand for Xiaomi's, iphone, Huawei, etc... ... Charging dock. Hole for cable, speaker and mic ! ...

This is a Docking Station for the Gear S3 and the Note 8 but obviously it will work for similar Phones and Watches. There are 2 version. I suggest Version 2 since Version 1 doesn't have the wider platform to stabilize when only the watch is on the...

No place for the charged phone not only make people inconvenient but also might cause other problems, since phones are the things we contact the most, dirt on the phone could influence people directly and shortly. Thus, I design this product to...

... might be able to sand some material away, or buy a smaller/thinner charging cable. Note that your phone should have the charging port in the middle of the phone (on the bottom, of course), in order for this charging stand/dock to properly work.

------------------------------------------------------------------------------------------------------------------------- Cellphone charging stand. You must put the cable through the round holes and set the phone in the center of the piece. (You...

This is my draft design for a phone stand/charging dock, feel free to modify this as it is not that good. ...:)

... no glue needed there. I recommend to use sticky pads under the phone charging dock. ...That way you will be able to take phone from the dock just using one hand and if needed sticky pad can just peel off and reuse it again in different location.

Note that your phone should have the charging port in the middle of the phone (on the bottom, of course), in order for this charging stand/dock to properly work. Support If you want to support me for the designs I publish for free, please consider...

Note that your phone should have the charging port in the middle of the phone (on the bottom, of course), in order for this charging stand/dock to properly work. Support If you want to support me for the designs I publish for free, please consider...

Note that your phone should have the charging port in the middle of the phone (on the bottom, of course), in order for this charging stand/dock to properly work. Support If you want to support me for the designs I publish for free, please...

This is a mobile phone charging dock. The Charger Model of Samsung charging pad is EP-PG9201 with an outer circumference of approximately 96mm Print instructionsPrint material is HT PLA, brand is ProtoPasta. The pad holder requires supports.

This is a universal charging dock inspired on this one: https://www.thingiverse.com/thing:1698964 The Dock.stl is the same for all phones, whilst the Holder.stl can be replaced for each connector/cable. The one provided in the files works perfectly...

It doesn't cost you anything extra, but helps me out a lot :) Print instructionsCategory: Mobile Phone Summary This phone dock has an integrated cable routing "hole", that allows you to charge your phone whilst it is on the stand/dock. If the size of...

Phone charging dock, was designed for the Samsung Galaxy S7 Edge (with case) though I have tested with various types of phones, it will fit and charge if the connection port is at the bottom of the phone in the centre. Print Settings Printer Brand: ...

see http://www.thingiverse.com/thing:957516 ) Instructions You need: -wireless charging cover installed on your phone. This fits phones width less than 83mm wide. wireless charging puck, I used Powerbot P1020, but any qi charger less than 27mm...

see http://www.thingiverse.com/thing:957516 )InstructionsYou need: -wireless charging cover installed on your phone. This fits phones width less than 83mm wide. wireless charging puck, I used Powerbot P1020, but any qi charger less than 27mm...

Phone dock for charging on wireless base. The wireless charger recess will accept a 100mm x 10mm disk that seems to be a pretty common size. I have noticed that the side to side movement of my phone on the base will cause the charger not to charge so...

Charging stand for smart phone.  Designed for the Google Pixel 3a XL (shown in photo).  The cord holder is designed to fit a standard usb-c cord, though it should also fit lightning cables and micro-usb as well. 

A dock for your phone. You can put a cable through the hole at the front to be fixed by the added clip. Simply use some glue to hold the clip in place. ...The cable can then be connected to a computer/charger.

Smart phone-charging stand, easy to build and nice to look at! Works for all chargers with a size of 12x6mm. How to build: 1. Plug the charger into the hole, maybe you have to grind something off. 2. Then clamb the cable in the slot. ...

... stand I designed. ...You can plug your phone in on the bottom and there are holes for the speakers as well. Should work on most phones. Mine is the iPhone 7 Plus and it works great with that. I'll be upgrading it to work with more phones too. ...

Also created in summer camp modeled to iphone 6 plus specs but it should work with other phones

Made for a friend as he wants to build his own.-Cord is just a long cylinder and their is no hole to reach the phone as it has not been decided what type of cord will be used.-Phone is based on the LG Stylo 4 but it not a completely accurate...