cetme receiver flat 3d models

I'm standing under a pedestal that's situated right beneath the Dreambox satellite receiver. ...A glowing filament made of high-quality ABS plastic is visible to my eyes.

This is a clip-on holder for a Spektrum AR10100T 10-channel telemetry receiver. ...It can be mounted on a support in your airplane either by using sticky tape or 2 M3 screws.

Simple holder designed specifically for the Jeti REX7 Receiver. For added stability, consider placing a rubber band over the top of the holder. ...This model prints well with 10% infill and without any support structures.

... is remarkably effective, allowing easy access to the bind-button and LED lights. ...Simply slide in the receiver. ... Originally designed for the FlyFox digital 215, this mount fits perfectly with standard 28mm standoffs - no modifications required.

Receiver tanks equipped with cyclone separators consistently produce superior air quality compared to traditional systems. ...These advanced separators efficiently remove moisture from compressed air by capturing it before it enters the storage...

RAD Li-ion receiver cover, for use when mounted on the underside like I do. I print it with two walls and 35% infill. ... Requires an 8mm standoff, M3 washer and 12 or 14mm button head M3 fastener.

A friend of mine had lost a knob for their speaker receiver and I modeled up one based off of another from the same unit. Printed in Hatchbox black pla

m4 airsoft receiver endcap 25,5 mm deep. ...30,5 in total length you can make it shorter in your slicer by dragging it under the bed in the program if you use CURA

This issue becomes even more crucial when combined with my modification, a removable wing design, which requires fast access to the receiver for easy servo connection to the ailerons. ... To ensure both parts stay together securely, you will need a...

FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...

This is the new Vertical Slider for the Optical receiver 3-axis mount, designed specifically for use with the Optical Rail System in order to securely mount the receiver. To complete the 3-axis mount, you will also need a Horizontal Slider and a...

Key Features: - Compatible with the Futaba R617FS receiver - Sturdy construction for reliable performance - Easy installation and minimal setup time - Suitable for a wide range of applications By investing in our mount bracket, you can trust that...

This print is specifically designed for receivers with the servo pins and bind button on the same side of the main board, as some receivers have their servo pins soldered on the reverse side. Please see photos, and check your receiver before...

This is a collection of antenna mounts for the ExpressLRS 2.4 EP1 receiver from Happymodel that I designed to use in my TBS Source One frame, but I guess they work in any frame with 5mm diameter spacers. There are three options: 1. Rear Vert...

For optimal performance, we recommend using our Marine GPS Antenna / Receiver Holder indoors, where it will be protected from the harsh elements. The low thickness and lack of UV resistance in most PET filaments make it an ideal choice for indoor...

This is a collection of antenna mounts for the ExpressLRS 2.4 EP1 receiver from Happymodel that I designed to use in my TBS Source One frame, but I guess they work in any frame with 5mm diameter spacers.There are three options:Rear Vert Short. For...

The goggles come with covers over the receivers, but they have holes in them which isn't a big deal if you use the cover for the front of the goggles, but I'm not into bling so I made a blank cover without holes to pop into the empty bay. I used it...

With this initial release the stock ESC is still needed though a clip for no ESC (in the stock location) is on the way. This fits both the stock receiver box and the Vitavon aluminum mount (as pictured). To complete you'll need: 2 x...

To complete you'll need: 2 x M3x10mm (12mm is ok too) for the cap retainer 2 x M3 nuts (locknut optional) for the cap retainer 1 x M3x20mm (or so) to allow the cap to screw into the stock location The stock gasket is required and you'll need to take...

The standard configuration allows a small foam pad to be attached, minimizing vibrations that reach the receiver, while the low-profile option is perfect for electric applications. This versatile plate features four screw mounting points or can be...

A Case for Protecting the FlySky/Turnigy X6B RC Receiver.\r\n\r\nOne of this receiver's features is its compact and "naked" design, but it leaves it vulnerable to damage in the harsh world of RC systems if not properly protected. ...Perhaps someone will...

Ultimately, I purchased a zipper case for the mouse and decided to make a holder for the receiver. This should be printed in TPU (or some other flexible filament). ...It grips fairly tightly and should not let the adapter fall out unintentionally.</p>...

Models of Traxxas TRX4 box cover: 1) with window 2) without window window enables You to look inside the box and check wether receiver light is blinking and receiver is working. This window lets You check presence of water in case Your TRX4 is...

FrSky X8R Receiver & Antenna Mount - I designed this specifically for use with the FireFly http://www.thingiverse.com/make:235170 printable drone, which demanded a more secure mounting solution that shielded my receiver from damage. After scouring...

I purchased a Logitech MX Master and was shocked to discover that the Unifying Receiver lacked on-device storage. Frustrated with this limitation, I opted to buy a zipper case for the mouse and designed a holder specifically for the receiver. This...

This allows you to house the key fob receiver when replacing the rear view mirror. Tri-lobe mirror adapters, usually marketed for dodge/ram/chrysler, also fit our Z3's. I mounted a smaller, adjustable rear view mirror using one of these adapters....

Simple 20x20 stack mount for the Happymodel EP1 ELRS receiver. ...I designed it specifically for the rear stack on the TBS Source One v5, but it's standard 20x20 so I'm sure it'll work in a lot of different applications.Designed with TPU in mind, but it...

This is a specialized adapter designed specifically for the Frsky G-RX8 receiver, allowing you to seamlessly integrate it into your remote control (RC) models. ...Its innovative design ensures that the antennas are always positioned at precisely 90...

The receiver sits comfortably within the bay, securely held in place with a strip of double-sided tape at its base. ... Settings and Guidelines for Optimal Performance Pre-Configuration Specifications Layer Thickness: Set to 0.20 Filling Ratio:...

... one of these materials, you may not need a finger hole in the back. However, I strongly advise against printing this cover with standard filaments because the fit is extremely tight, and you risk breaking the case when trying to remove the receiver.